2210 Loader Valve
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 16
Like Tree16Likes

Thread: 2210 Loader Valve

  1. Top | #1
    cs1
    cs1 is offline

    Join Date
    Jan 2019
    Last Online
    05-25-2019 @ 06:34 PM
    Location
    Chicago
    Posts
    16
    Thanks
    0
    Thanked 0 Times in 0 Posts

    2210 Loader Valve

    Hi
    I just put a front end loader on my 2210 that I bought last year. It will not raise. It only goes up 3 feet and it takes over a minute to get there. I replaced the coupler for the lift hose, but it is not the couplers. I also cleaned the strainer in the side of the transaxle.

    I can get it to raise if I pull the handle back and then slightly to the left, then when it gets halfway I have to move it all the way to the back left. But it takes several minutes to raise. The bucket curl does not seem to be too bad but it could be a little faster.

    Does anyone have any idea? I think there is problem with the valve.

    The loader is brand new.
    Last edited by cs1; 03-30-2019 at 07:22 PM.
    raco232 likes this.

  2. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

  3. Top | #2
    Captain Hook Kennyd's Avatar
    Join Date
    Aug 2010
    Last Online
    Today @ 08:06 PM
    Location
    Westminster, MD
    Posts
    15,887
    Thanks
    4,798
    Thanked 3,807 Times in 2,415 Posts
    Welcome to GTT
    Did you replace just one coupler? Or the pair on the lift/lower circuit?
    Have you verified the linkage it moving the spool all the way?
    Kenny

    -John Deere 3720 Deluxe Cab TLB
    FEL, MMM, Artillian 42" Forks and Modular Grapple, I-Match, Ballast Box, Trac-Vac 854 (for sale) and lots of other STUFF.
    -John Deere 455 w/60" MMM


    Bolt on Grab Hooks and other cool stuff are now for sale!!

    Visit our YouTube Channel

    My Equipment:
    John Deere 3720 Deluxe Cab, 300cx FEL, 366 Front Blade, 59" Front Snowblower, Ballast Box
    Artillian 3K Forks, Grapple, Front-Hoe Bucket
    John Deere 455, 60" MMM

  4. Top | #3
    cs1
    cs1 is offline

    Join Date
    Jan 2019
    Last Online
    05-25-2019 @ 06:34 PM
    Location
    Chicago
    Posts
    16
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Hi
    I only did the one coupler to start with. I had my doubts that was it. I goes down fine after you get it raised, too fast in fact, and the orifice is in the blue hose. And yes, I watched the spool on the valve and it goes all the way in. I have a feeling fluid is being bypassed in the valve, or the pressure relief springs on the valve are shot. There are 2, one on top and one on bottom.

    Should I try a coupler on the other hose. I took the other one apart, I just don't see what could be wrong with them.
    raco232 likes this.

  5. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

  6. Top | #4
    fdmars's Avatar
    Join Date
    Feb 2011
    Last Online
    Today @ 06:10 PM
    Location
    Mid CT
    Posts
    2,044
    Thanks
    150
    Thanked 186 Times in 147 Posts
    To help isolate problem can you switch the circuits and see if problem persists?
    raco232 likes this.
    2009 JD 2305 w/ Femco folding ROPS,Power Beyond Kit, KBOH, 54"MMM, 47" Snowblower, 200CX Loader w/ BB, Powerhorse 12 ton Logsplitter and King Kutter tool carrier and 17P kart
    2009 Cub Cadet/Yanmar ex3200, Land Pride 60” land plane and 60” finish mower, worksaver posthole digger w/ 9” auger, “The thumb” add on grapple, third function valve and KBOH of course

  7. Top | #5
    raco232's Avatar
    Join Date
    Nov 2015
    Last Online
    Today @ 04:19 PM
    Location
    Memphis, Mississippi
    Posts
    562
    Thanks
    74
    Thanked 51 Times in 44 Posts
    Maybe find out what the hyd psi the tractor ought to be delivering at the loader coupling and couple up a psi gauge to verify psi.
    fdmars likes this.
    2012 JD2520 R4's.
    200CX Loader, 49" bucket
    Imatch quick hitch
    King Kutter 60" tiller
    Howse 60" Box blade
    Howse 16" Single bottom plow
    Dirt Dog 5 Shank Chisel Plow (60")
    Homemade 3pt suitcase weight hitch
    Homemade 3pt 1 row disc hiller
    Homemade (6) shank toothbar
    (4) 2" Motorsports Wheel Spacers
    (7) 70lb suitcase weights
    Ken's bolt on hooks
    Titan 42" pallet forks

  8. Top | #6
    Captain Hook Kennyd's Avatar
    Join Date
    Aug 2010
    Last Online
    Today @ 08:06 PM
    Location
    Westminster, MD
    Posts
    15,887
    Thanks
    4,798
    Thanked 3,807 Times in 2,415 Posts
    Bad couplers can act as a check valve, so there is a possibility you still have a bad one. What loader did you purchase? Did your tractor ever have a backhoe or the power beyond kit installed?

    Getting a gauge to do some testing might be a good idea, the valves themselves very rarely go bad so I don't think that's it.
    Kenny

    -John Deere 3720 Deluxe Cab TLB
    FEL, MMM, Artillian 42" Forks and Modular Grapple, I-Match, Ballast Box, Trac-Vac 854 (for sale) and lots of other STUFF.
    -John Deere 455 w/60" MMM


    Bolt on Grab Hooks and other cool stuff are now for sale!!

    Visit our YouTube Channel

    My Equipment:
    John Deere 3720 Deluxe Cab, 300cx FEL, 366 Front Blade, 59" Front Snowblower, Ballast Box
    Artillian 3K Forks, Grapple, Front-Hoe Bucket
    John Deere 455, 60" MMM

  9. Top | #7

    Join Date
    Dec 2015
    Last Online
    Today @ 03:21 PM
    Location
    North Carolina
    Posts
    1,252
    Thanks
    71
    Thanked 172 Times in 159 Posts
    Quote Originally Posted by cs1 View Post
    Hi
    I just put a front end loader on my 2210 that I bought last year. It will not raise. It only goes up 3 feet and it takes over a minute to get there. I replaced the coupler for the lift hose, but it is not the couplers. I also cleaned the strainer in the side of the transaxle.

    I can get it to raise if I pull the handle back and then slightly to the left, then when it gets halfway I have to move it all the way to the back left. But it takes several minutes to raise. The bucket curl does not seem to be too bad but it could be a little faster.

    Does anyone have any idea? I think there is problem with the valve.

    The loader is brand new.
    I used to have a 2210. If you don't hook the hoses up in the correct spots then the loader will act funny like this. Are the 4 hoses plugged into the valve correctly? When I first got my tractor the color coded plugs were missing so it was a guessing game for me until I got it figured out. Also if the connections are not absolutely cleaning then the hoses don't quite hook up and you will have issues like this.

    I am assuming you found a factory loader to put on this 2210? I have never seen an after market loader for a 2210 but I am sure someone may have produced one.
    3025e, D160 loader, Artillian Grapple, Forks, Hoe Bucket, Frontier Land Plane, Rotomec PDH300, Redline Systems 54 inch rock bucket, Heavy Hitch
    400 Garden Tractor, 35a Tiller, 54 inch plow, 60 inch deck

  10. Top | #8
    cs1
    cs1 is offline

    Join Date
    Jan 2019
    Last Online
    05-25-2019 @ 06:34 PM
    Location
    Chicago
    Posts
    16
    Thanks
    0
    Thanked 0 Times in 0 Posts
    I will get the other couplers and a gauge. I bought an H130 loader. New at more than 50% off.
    The tractor never had a loader on it or a backhoe. There is no power beyond. I had to add the loader valve. I found it on ebay along with the steel lines, couplers and the bracket that holds them on. Everything I needed to put it on my tractor.

    If I take the bucket off it will lift the arms.

  11. Top | #9
    cs1
    cs1 is offline

    Join Date
    Jan 2019
    Last Online
    05-25-2019 @ 06:34 PM
    Location
    Chicago
    Posts
    16
    Thanks
    0
    Thanked 0 Times in 0 Posts
    I am sure I have them hooked up correctly. I followed the instruction that came with the loader and when I move the lever, back is up forward in down. left is bucket curl back and right is bucket dump.

    The loader is a new H130.
    69project likes this.

  12. Top | #10
    Captain Hook Kennyd's Avatar
    Join Date
    Aug 2010
    Last Online
    Today @ 08:06 PM
    Location
    Westminster, MD
    Posts
    15,887
    Thanks
    4,798
    Thanked 3,807 Times in 2,415 Posts
    Since your 2210 did not have the SCV, I assume you added the spacer plate too? If the machine it came from had the PB installed then the plug (#4) would be installed, that would affect how the valve operates. This ONLY should be there if the power beyond lines are added.

    Next step is a gauge to test each port.
    Attached Thumbnails Attached Thumbnails Capture.JPG  
    Kenny

    -John Deere 3720 Deluxe Cab TLB
    FEL, MMM, Artillian 42" Forks and Modular Grapple, I-Match, Ballast Box, Trac-Vac 854 (for sale) and lots of other STUFF.
    -John Deere 455 w/60" MMM


    Bolt on Grab Hooks and other cool stuff are now for sale!!

    Visit our YouTube Channel

    My Equipment:
    John Deere 3720 Deluxe Cab, 300cx FEL, 366 Front Blade, 59" Front Snowblower, Ballast Box
    Artillian 3K Forks, Grapple, Front-Hoe Bucket
    John Deere 455, 60" MMM

  13. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

Page 1 of 2 1 2 LastLast

Similar Threads

  1. First tractor, 2210 with loader, how to snowblow and move wood
    By tinkertot in forum Sub Compact Utility Tractors (SCUT)
    Replies: 26
    Last Post: 10-31-2016, 06:51 AM
  2. JD 2210 and 210 Loader Connect Issue
    By jwakeman in forum Sub Compact Utility Tractors (SCUT)
    Replies: 5
    Last Post: 08-21-2015, 08:10 AM
  3. 2210 Loader
    By bikerdave11 in forum Sub Compact Utility Tractors (SCUT)
    Replies: 10
    Last Post: 10-19-2014, 09:48 AM
  4. 2210 loader problem
    By bikerdave11 in forum Sub Compact Utility Tractors (SCUT)
    Replies: 2
    Last Post: 10-16-2014, 07:42 PM
  5. Replies: 6
    Last Post: 03-24-2014, 12:52 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •