1985 JD 1050 with 75 Loader
Results 1 to 6 of 6
Like Tree1Likes
  • 1 Post By GrowinBucks

Thread: 1985 JD 1050 with 75 Loader

  1. Top | #1

    Join Date
    Mar 2019
    Last Online
    Yesterday @ 03:23 PM
    Posts
    9
    Thanks
    0
    Thanked 0 Times in 0 Posts

    1985 JD 1050 with 75 Loader

    Ok guys..had a leak at the junction for the Bucket Cylinders. I took both Hard Lines/Rubber apart. Cleaned/Cleared etc...and put back tight. Now Bucket doesnt curl. The lift goes up and down, but no curl. The SCV is sketchy you have to tweak handles so the lift will work properly....even after going through and changing orings to dealer bought replacements.
    I am assuming air. Have worked every Hydro part every which way numerous times to try and work air out. Bucket right now is facing all the way down. It twitches but like it hits a lock after an inch or so. I even tried to push it past the point with the Mrs. Pulling lever back. I could push further than it would itself, but right back down.
    Loosening connections on bucket cylinder on both sides have pressure...

    "Maybe I hooked them up backwards?" Well doesnt work either way you swap lines on front. So...brings me to the Diagram. If i am reading this correct. The Lift Cylinders are plumbed cylinder to cylinder and rod to rod...the bucket however shows me that they cris-cross?? I dont know Hydros, but is that correct or should they be cylinder to cylinder and rod to rod as well. Regardless bucket wont curl either way..

    All fluids have been changed, new filters etc...all clear...

    Any ideas?
    Attached Thumbnails Attached Thumbnails Screenshot_20190702-155648_Samsung Internet_1562097468450.jpg   Screenshot_20190702-155622_Samsung Internet_1562097497687.jpg  

  2. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

  3. Top | #2
    Keeper of the GTT Cookies dieselshadow's Avatar
    Join Date
    Nov 2011
    Last Online
    Today @ 09:06 PM
    Location
    Joelton TN
    Posts
    19,510
    Thanks
    1,048
    Thanked 4,152 Times in 2,520 Posts
    More than likely your quick connects aren’t fully seated. Remove them, clean, and re-insert.
    - Jason

    GreenTractorTalk.com Rules, Policies, and Terms of Use

    Subscribe to dieselshadowman on YouTube

    2720 w/ 200CX FEL
    , Ken's weld-on hooks, Fit Rite Hydraulics Top and Tilt kit, Artillian forks.
    1954 60 - getting full restoration, 1964
    110 round fender in the shop for crustoration
    Ferris IS3200Zzero turn mower

  4. Top | #3
    flyweight's Avatar
    Join Date
    Jun 2014
    Last Online
    Today @ 08:52 PM
    Location
    Louisiana, (the Tropics of)
    Posts
    9,229
    Thanks
    786
    Thanked 1,704 Times in 1,170 Posts
    Quote Originally Posted by GrowinBucks View Post
    So...brings me to the Diagram. If i am reading this correct. The Lift Cylinders are plumbed cylinder to cylinder and rod to rod...the bucket however shows me that they cris-cross?? I dont know Hydros, but is that correct or should they be cylinder to cylinder and rod to rod as well. Regardless bucket wont curl either way.
    The bucket cylinder hose diagram is wrong.


    Quote Originally Posted by dieselshadow View Post
    More than likely your quick connects aren’t fully seated. Remove them, clean, and re-insert.
    Ditto.
    Michael

    '84 JD 750
    '08 JD Z445
    '71 JD 15 Chainsaw
    And a bunch of other stuff.


    " If there's no one around to smell me, do I really stink"?
    - John Wells - Brewster County, West Texas.










  5. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

  6. Top | #4

    Join Date
    Mar 2019
    Last Online
    Yesterday @ 03:23 PM
    Posts
    9
    Thanks
    0
    Thanked 0 Times in 0 Posts
    No quick cons...screw in hoses throughout. Need to get some though!!

    I agree that the diagram in the Manual is wrong..just wanted to make sure.

    What else.

  7. Top | #5
    theduke's Avatar
    Join Date
    Feb 2016
    Last Online
    Today @ 09:14 PM
    Location
    NW Oregun...the Wet Side.... Gaston
    Posts
    560
    Thanks
    25
    Thanked 100 Times in 69 Posts


    Is it possible you have one side reversed?

    One is trying to go out while the other is trying to go in...resulting in

    What you have there.


    You'd only know if they were unhooked from the bucket which is a pita.

    on my 70a loader....the hoses from the curl cylinders...top hoses of both hook to the same Hard line.
    Same with the bottom hoses...both hook to "That" same hardline.

    If you had it all apart it would be easy to hook hoses to the wrong spot as they would easily reach the way its plumbed.

    If possible post some pics of the area you were working on...loader lines/hoses
    Last edited by theduke; 07-02-2019 at 08:25 PM.
    Dan


    JD 955 ,70A loader, 60" mmm , Original I-match ,4' woods B hog , 5' Box blade , 12' orchard plane/driveway grader ,various other doo-dads & homebuilt implements. Goossen BFBlower, JakeRake..this thing is different.
    Kubota U-15
    Kubota RTV 900

  8. Top | #6

    Join Date
    Mar 2019
    Last Online
    Yesterday @ 03:23 PM
    Posts
    9
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Well!...HaHaHa...when all else fails, start from square! Exactly as the Duke said. I had my wires crossed...what a Dumbo! Had the Bucket rod and the Lift Cylinder hoses swapped at the SCV.

    Working like a New one now...

    Lesson Learned...again...its usually the Simple Things!

    "If at first you don't succeed, destroy all evidence that you ever tried!"...now how to Delete this Thread haha..

    Thanks Guys! Not a lot of info out there in writing anymore on this Old Deere!
    theduke likes this.

  9. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •