OK for implements on pallets for 1025r JD QH connect?
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 11
Like Tree18Likes

Thread: OK for implements on pallets for 1025r JD QH connect?

  1. Top | #1

    Join Date
    Jul 2016
    Last Online
    Today @ 03:54 PM
    Location
    Austin TX
    Posts
    2,497
    Thanks
    29
    Thanked 560 Times in 418 Posts

    OK for implements on pallets for 1025r JD QH connect?

    Probably not a problem, but have never had the 3ph on yet & have read about its limited lift distance. Mostly concerned about new, heavy 60" LP on its pallet that I won't be able to move with forks after taking off the BH. Want to be sure I'll be able to just back up & connect.

  2. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

  3. Top | #2

    Join Date
    Jan 2012
    Last Online
    Today @ 06:19 PM
    Location
    East Central Indiana
    Posts
    1,483
    Thanks
    94
    Thanked 242 Times in 174 Posts
    I do not believe you will have a problem, but it depends on how high the hitch pins are.
    I used to have a 1026R. I kept a 3 point tiller & box blade on carts with casters on them. The carts were taller than a pallet. I did not have any hooking those up.
    Kioti CK3510SE HST, Kioti KL4030 Loader, John Deere 655 Tiller, Frontier LR2072 Landscape Rake, Virnig V50 Pallet Forks, Woods GB60 Box Blade
    John Deere X739 AWS 4X4, 60HC Auto Connect Deck, Front grader blade.
    John Deere 825i Gator

    John Deere Tractors I have owned in the past.
    425 AWS, 455, 4400, 2210, 4710, 2320, 2720, X475, 1026R, 4120, 2025R

  4. Top | #3
    coaltrain's Avatar
    Join Date
    May 2014
    Last Online
    Today @ 05:57 PM
    Location
    NW Penna
    Posts
    20,214
    Thanks
    1,099
    Thanked 3,112 Times in 2,274 Posts
    If you are concerned take the implement off the pallet while you have the loader/backhoe on. Then switch over to the 3 point hitch and go.

    Worse case scenario is to drag the implement off the pallet with a chain. You aren’t going to hurt anything.
    wentonbrown, theduke and trboxman like this.
    ~Stan~
    It is what it is
    Knowledge is power, ignorance is bliss
    2520 w/200CX w/62D2

  5. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

  6. Top | #4

    Join Date
    Jul 2016
    Last Online
    Today @ 03:54 PM
    Location
    Austin TX
    Posts
    2,497
    Thanks
    29
    Thanked 560 Times in 418 Posts
    Quote Originally Posted by coaltrain View Post
    If you are concerned take the implement off the pallet while you have the loader/backhoe on. Then switch over to the 3 point hitch and go.

    Worse case scenario is to drag the implement off the pallet with a chain. You aren’t going to hurt anything.
    Currently the pallet is on a concrete pad, so don't think I'd be wanting to drag the LP with chains. Thought the level pad would be best for my 3ph initiation. How else could I get the LP off of the pallet other than using the 3ph? Remember my skill level with the forks.

  7. Top | #5
    coaltrain's Avatar
    Join Date
    May 2014
    Last Online
    Today @ 05:57 PM
    Location
    NW Penna
    Posts
    20,214
    Thanks
    1,099
    Thanked 3,112 Times in 2,274 Posts
    Quote Originally Posted by dianedebuda View Post
    Currently the pallet is on a concrete pad, so don't think I'd be wanting to drag the LP with chains. Thought the level pad would be best for my 3ph initiation. How else could I get the LP off of the pallet other than using the 3ph? Remember my skill level with the forks.
    Ummm - with the forks of course!

    You can do it - you can’t hurt anything. A land plane is made to drag through the dirt and rocks - there built pretty tough.

    You could actually attach a chain to 2 corners with some slack - then lift the chain with your forks.
    wentonbrown and trboxman like this.
    ~Stan~
    It is what it is
    Knowledge is power, ignorance is bliss
    2520 w/200CX w/62D2

  8. Top | #6

    Join Date
    Feb 2018
    Last Online
    06-17-2019 @ 01:42 PM
    Location
    Montana - East slopes of the Rockies
    Posts
    322
    Thanks
    38
    Thanked 34 Times in 30 Posts
    <deleted>
    Last edited by Roger47; 06-10-2019 at 09:07 PM.
    2032R classic, H130 Loader, 46 Backhoe, 54" Snowblower,
    214 (1978), 46 mower with powerflow bagger, 31 tiller, 37A snow thrower
    some other stuff

  9. Top | #7
    Captain Hook Kennyd's Avatar
    Join Date
    Aug 2010
    Last Online
    Today @ 06:24 PM
    Location
    Westminster, MD
    Posts
    16,460
    Thanks
    5,072
    Thanked 4,092 Times in 2,553 Posts
    IF it's problem, just place some 2x6's on the ground as ramps for the rears wheels, that will gain you 1.5" or 3" of height.
    mark02tj, jdforever, keane and 1 others like this.
    Kenny

    -John Deere 3720 Deluxe Cab TLB
    FEL, MMM, Artillian 42" Forks and Modular Grapple, I-Match, Ballast Box, and lots of other STUFF.
    -John Deere 455 w/60" MMM


    Bolt on Grab Hooks and other cool stuff are now for sale!!

    Visit our YouTube Channel

    My Equipment:
    John Deere 3720 Deluxe Cab, 300cx FEL, 366 Front Blade, 59" Front Snowblower, Ballast Box
    Artillian 3K Forks, Grapple, Front-Hoe Bucket
    John Deere 455, 60" MMM

  10. The Following User Says Thank You to Kennyd For This Useful Post:

    mark02tj (06-11-2019)

  11. Top | #8

    Join Date
    Jul 2016
    Last Online
    Today @ 03:54 PM
    Location
    Austin TX
    Posts
    2,497
    Thanks
    29
    Thanked 560 Times in 418 Posts
    Quote Originally Posted by Kennyd View Post
    IF it's problem, just place some 2x6's on the ground as ramps for the rears wheels, that will gain you 1.5" or 3" of height.
    Perfect. Now why didn't I think of that?

  12. Top | #9
    Captain Hook Kennyd's Avatar
    Join Date
    Aug 2010
    Last Online
    Today @ 06:24 PM
    Location
    Westminster, MD
    Posts
    16,460
    Thanks
    5,072
    Thanked 4,092 Times in 2,553 Posts
    Quote Originally Posted by dianedebuda View Post
    Perfect. Now why didn't I think of that?
    Because your a woman?






    No but seriously, we all overlook the obvious sometimes in search of a complicated solution.
    Kenny

    -John Deere 3720 Deluxe Cab TLB
    FEL, MMM, Artillian 42" Forks and Modular Grapple, I-Match, Ballast Box, and lots of other STUFF.
    -John Deere 455 w/60" MMM


    Bolt on Grab Hooks and other cool stuff are now for sale!!

    Visit our YouTube Channel

    My Equipment:
    John Deere 3720 Deluxe Cab, 300cx FEL, 366 Front Blade, 59" Front Snowblower, Ballast Box
    Artillian 3K Forks, Grapple, Front-Hoe Bucket
    John Deere 455, 60" MMM

  13. Top | #10

    Join Date
    Jul 2016
    Last Online
    Today @ 03:54 PM
    Location
    Austin TX
    Posts
    2,497
    Thanks
    29
    Thanked 560 Times in 418 Posts
    Quote Originally Posted by Kennyd View Post
    Because your a woman?




  14. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

Page 1 of 2 1 2 LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •