Steering Wheel Spinner Knob recommendation for 1025R
Page 1 of 11 1 2 3 ... LastLast
Results 1 to 10 of 106
Like Tree613Likes

Thread: Steering Wheel Spinner Knob recommendation for 1025R

  1. Top | #1
    biodiesel's Avatar
    Join Date
    Feb 2019
    Last Online
    10-14-2019 @ 07:27 PM
    Location
    New Mexico
    Posts
    86
    Thanks
    6
    Thanked 2 Times in 2 Posts

    Steering Wheel Spinner Knob recommendation for 1025R

    I'm loving my new 1025R, but I have come to realize that I could probably benefit from a steering wheel spinner knob. Does anyone have one that you recommend? I saw this one online (TY26583), but someone said it didn't fit their 1023E, which I would think would be the same steering wheel as the 1025R.

    Click image for larger version. 

Name:	TY26583-0-1.jpg 
Views:	334 
Size:	26.0 KB 
ID:	707254
    glc, mdgilbreath and Marlin like this.
    2019 - John Deere 1025R, 120R Loader, 260 Backhoe, Block Heater, iMatch, Frontier AP10F Pallet Forks

    2019 - Iron Bull Utility Trailer, 83”x16', 10,000 GVWR
    2018 - Iron Bull Dump Trailer, 6'x12', 10,000 GVWR
    Stihl saws - MS 271 Farm Boss, 034, HT 56 C-E

  2. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

  3. Top | #2
    rakane's Avatar
    Join Date
    Aug 2017
    Last Online
    Yesterday @ 11:57 PM
    Location
    Warren, Oregon USA
    Posts
    464
    Thanks
    79
    Thanked 48 Times in 42 Posts
    That fit on my 1025R although tilted a bit toward the center. A must have.

    Sent from my SM-N950U using Tapatalk
    Marlin and biodiesel like this.

  4. Top | #3
    Keeper of the GTT Cookies dieselshadow's Avatar
    Join Date
    Nov 2011
    Last Online
    Today @ 10:27 AM
    Location
    Joelton TN
    Posts
    19,920
    Thanks
    1,067
    Thanked 4,328 Times in 2,601 Posts
    They work very well and fit perfectly fine ONLY if trim the piece of rubber to fit the wheel where it's more flat than round. Then the spinner can grab at any angle you set it to. All of mine have been set up this way with the modern "not perfectly round" (cross section wise) steering wheels.
    - Jason

    GreenTractorTalk.com Rules, Policies, and Terms of Use

    Subscribe to dieselshadowman on YouTube

    2720 w/ 200CX FEL
    , Ken's weld-on hooks, Fit Rite Hydraulics Top and Tilt kit, Artillian forks.
    1954 60 - getting full restoration, 1964
    110 round fender in the shop for crustoration
    Ferris IS3200Zzero turn mower

    Quote Originally Posted by Gizmo2 View Post
    Dieselshadow is my Hero.


  5. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

  6. Top | #4
    biodiesel's Avatar
    Join Date
    Feb 2019
    Last Online
    10-14-2019 @ 07:27 PM
    Location
    New Mexico
    Posts
    86
    Thanks
    6
    Thanked 2 Times in 2 Posts
    Quote Originally Posted by dieselshadow View Post
    They work very well and fit perfectly fine ONLY if trim the piece of rubber to fit the wheel where it's more flat than round. Then the spinner can grab at any angle you set it to. All of mine have been set up this way with the modern "not perfectly round" (cross section wise) steering wheels.
    When you say trim, you mean trimming the bracket, not the steering wheel, right?
    Marlin likes this.
    2019 - John Deere 1025R, 120R Loader, 260 Backhoe, Block Heater, iMatch, Frontier AP10F Pallet Forks

    2019 - Iron Bull Utility Trailer, 83”x16', 10,000 GVWR
    2018 - Iron Bull Dump Trailer, 6'x12', 10,000 GVWR
    Stihl saws - MS 271 Farm Boss, 034, HT 56 C-E

  7. Top | #5
    Keeper of the GTT Cookies dieselshadow's Avatar
    Join Date
    Nov 2011
    Last Online
    Today @ 10:27 AM
    Location
    Joelton TN
    Posts
    19,920
    Thanks
    1,067
    Thanked 4,328 Times in 2,601 Posts
    No sir. Look at the spinner picture you posted again. It comes with a rubber strip to allow it to mount to smaller diameter steering wheels and give it better clamping force. All you need to do is trim that rubber strip to fit the wheel for a round fit. Let me go get a pic of mine. It'll make more sense.
    glc, Gizmo2, Duke Snyder and 4 others like this.
    - Jason

    GreenTractorTalk.com Rules, Policies, and Terms of Use

    Subscribe to dieselshadowman on YouTube

    2720 w/ 200CX FEL
    , Ken's weld-on hooks, Fit Rite Hydraulics Top and Tilt kit, Artillian forks.
    1954 60 - getting full restoration, 1964
    110 round fender in the shop for crustoration
    Ferris IS3200Zzero turn mower

    Quote Originally Posted by Gizmo2 View Post
    Dieselshadow is my Hero.


  8. Top | #6
    Keeper of the GTT Cookies dieselshadow's Avatar
    Join Date
    Nov 2011
    Last Online
    Today @ 10:27 AM
    Location
    Joelton TN
    Posts
    19,920
    Thanks
    1,067
    Thanked 4,328 Times in 2,601 Posts
    Here’s a couple of pics.

    Notice the spinner is perpendicular to the wheel. Without some sort of correction, the spinner will lean inwards with no way to control that.



    Here’s the rubber strip trimmed and fit in the correct spot.



    Easy peasy.
    glc, Gizmo2, Duke Snyder and 12 others like this.
    - Jason

    GreenTractorTalk.com Rules, Policies, and Terms of Use

    Subscribe to dieselshadowman on YouTube

    2720 w/ 200CX FEL
    , Ken's weld-on hooks, Fit Rite Hydraulics Top and Tilt kit, Artillian forks.
    1954 60 - getting full restoration, 1964
    110 round fender in the shop for crustoration
    Ferris IS3200Zzero turn mower

    Quote Originally Posted by Gizmo2 View Post
    Dieselshadow is my Hero.


  9. Top | #7
    biodiesel's Avatar
    Join Date
    Feb 2019
    Last Online
    10-14-2019 @ 07:27 PM
    Location
    New Mexico
    Posts
    86
    Thanks
    6
    Thanked 2 Times in 2 Posts
    Quote Originally Posted by dieselshadow View Post
    Here’s a couple of pics.

    Notice the spinner is perpendicular to the wheel. Without some sort of correction, the spinner will lean inwards with no way to control that.

    Here’s the rubber strip trimmed and fit in the correct spot.

    Easy peasy.
    Thank you! The pictures make it much easier to understand.
    Gizmo2, jdforever, Marlin and 1 others like this.
    2019 - John Deere 1025R, 120R Loader, 260 Backhoe, Block Heater, iMatch, Frontier AP10F Pallet Forks

    2019 - Iron Bull Utility Trailer, 83”x16', 10,000 GVWR
    2018 - Iron Bull Dump Trailer, 6'x12', 10,000 GVWR
    Stihl saws - MS 271 Farm Boss, 034, HT 56 C-E

  10. Top | #8

    Join Date
    Sep 2018
    Last Online
    Today @ 10:18 AM
    Location
    Pennsylvania
    Posts
    78
    Thanks
    13
    Thanked 7 Times in 7 Posts
    Quote Originally Posted by dieselshadow View Post
    Here’s a couple of pics.

    Notice the spinner is perpendicular to the wheel. Without some sort of correction, the spinner will lean inwards with no way to control that.



    Here’s the rubber strip trimmed and fit in the correct spot.



    Easy peasy.
    My oh my could you zoom in just a little more? I think I could download your finger prints on it then.
    BigJim55 and Marlin like this.

  11. Top | #9

    Join Date
    Sep 2019
    Last Online
    Today @ 04:46 AM
    Location
    Warrenton
    Posts
    4
    Thanks
    0
    Thanked 0 Times in 0 Posts
    I also have this type of spinner on my 317s. It makes them a lot easier to steer. I’m also thinking of putting one on my 1025R.


    Sent from my iPhone using Tapatalk

  12. Top | #10
    jgayman's Avatar
    Join Date
    Jul 2012
    Last Online
    Today @ 10:31 AM
    Location
    Central Pennsylvania
    Posts
    10,029
    Thanks
    371
    Thanked 1,659 Times in 1,257 Posts
    Some folks like myself actually prefer the knob canted inward slightly. :-)
    glc, Doug, mdgilbreath and 3 others like this.
    2012 2720 -- 200CX Loader -- 54" Quick Attach Snow Blower -- Frontier LR5060 Rake -- Land Pride RB1660 Blade (Hydraulic Angle) -- Artillian 42" Forks -- Ken's Bolt on Grab Hooks -- Fit Rite Hydraulic top-link -- 2013 X500 for mowing duties

  13. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

Page 1 of 11 1 2 3 ... LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •