200CX or H130 loader - oil line help
Results 1 to 6 of 6

Thread: 200CX or H130 loader - oil line help

  1. Top | #1

    Join Date
    Mar 2014
    Last Online
    Yesterday @ 06:47 PM
    Location
    Long Island, NY
    Posts
    311
    Thanks
    25
    Thanked 51 Times in 36 Posts

    200CX or H130 loader - oil line help

    I'm working on my 410 loader and am looking to replace the oil lines. I've found NOS for 3 of them but can't find the 4th one. JD still has it in the data base but when a dealer tries to order it they get no longer available. Can someone who's got either a 200CX or an H130 loader measure the lines to see if it would work on my 410? The part # for the 410 is AW30865. The 200CX and H130 part # is AW32944. It is the 3rd line back and the shortest one on the left side. The connections are about 9" up and the bend on the right side starts at about 24". From the bend to the connection is about 17".



    [IMG]
    [/IMG]



    2005 - JD 4110, 54" front blade, 47" snow blower
    2004 - JD X595, 54" front blade
    2000 - JD 4100, 410 FEL

  2. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

  3. Top | #2

    Join Date
    Mar 2014
    Last Online
    Yesterday @ 06:47 PM
    Location
    Long Island, NY
    Posts
    311
    Thanks
    25
    Thanked 51 Times in 36 Posts
    I'm looking for part 15 in this diagram.
    2005 - JD 4110, 54" front blade, 47" snow blower
    2004 - JD X595, 54" front blade
    2000 - JD 4100, 410 FEL

  4. Top | #3
    Guest
    Join Date
    Apr 2013
    Last Online
    01-22-2018 @ 08:31 PM
    Location
    Tennessee
    Posts
    1,919
    Thanks
    392
    Thanked 256 Times in 196 Posts
    Have you considered taking the line to a local hydraulic shop to have them make you a new one?

    Also, check out Green Farm Parts to see if they can get a genuine JD part.
    Last edited by 5304; 04-19-2016 at 08:23 PM.

  5. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

  6. Top | #4

    Join Date
    Mar 2014
    Last Online
    Yesterday @ 06:47 PM
    Location
    Long Island, NY
    Posts
    311
    Thanks
    25
    Thanked 51 Times in 36 Posts
    GFP was my first attempt. I ordered them online and was refunded my $ when they tried to order them from JD. The fittings for the hard lines are apparently made for JD as no one could match them. I could have hard lines made but for big $ with several extra fittings or go with hoses. I'm thinking the 200CX/H130 lines are probably going to be as close as I can get but want to make sure it will work before ordering one. My local dealer usually has several H130's on the lot but today they had none when I went to check.
    2005 - JD 4110, 54" front blade, 47" snow blower
    2004 - JD X595, 54" front blade
    2000 - JD 4100, 410 FEL

  7. Top | #5

    Join Date
    Sep 2015
    Last Online
    Yesterday @ 08:08 PM
    Location
    Burton, Ohio
    Posts
    2,778
    Thanks
    552
    Thanked 443 Times in 351 Posts
    As an emergency resort, if you are utterly unable to locate a new line then after careful measurement I would find a shop where you could ask them to cut off the fittings and drill the tubes out. Make up new tubes and silver solder the fittings back on.
    1025R FILB, vintage: 2015
    54D MM mowing deck
    Imatch hitch
    2 inch receiver for three point
    "18" cart
    Piranha Tooth Bar
    Ken's hooks and differential lock pedal
    Artillian 36" forks
    Stihl equipment: Saws; MS261C, MS462C, MS661RCM and Blower; BR600 and Trimmer; FS70R and Hedge Cutter; HL 56K and Pressure Washer; RB400
    Husky log splitter

  8. Top | #6

    Join Date
    Mar 2014
    Last Online
    Yesterday @ 06:47 PM
    Location
    Long Island, NY
    Posts
    311
    Thanks
    25
    Thanked 51 Times in 36 Posts
    Quote Originally Posted by Jeff B View Post
    As an emergency resort, if you are utterly unable to locate a new line then after careful measurement I would find a shop where you could ask them to cut off the fittings and drill the tubes out. Make up new tubes and silver solder the fittings back on.

    The old line and it's connections is pretty rusty and I'd like to remove as many rusty pieces as I can. It's still usable but I'd really like to replace it with something that looks like it belongs there.

    Thanks,
    Roger
    2005 - JD 4110, 54" front blade, 47" snow blower
    2004 - JD X595, 54" front blade
    2000 - JD 4100, 410 FEL

  9. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •