Another way to make your implements roll
Results 1 to 1 of 1
Like Tree1Likes
  • 1 Post By green and red man

Thread: Another way to make your implements roll

  1. Top | #1
    green and red man's Avatar
    Join Date
    Nov 2011
    Last Online
    08-26-2015 @ 08:08 PM
    Location
    x
    Posts
    1,245
    Thanks
    371
    Thanked 82 Times in 64 Posts

    Another way to make your implements roll

    Here's another method to move your implements around when low on storage space.

    For 3 point mowers and some other implements, this idea will allow you to keep the wheels on the implement with no extra cart or dolly to deal with.

    You start with a short length of 2 1/2 inch square tubing which will later be welded on or near the corners(but on the sides) of the brush hog or other implement. The wheel diameter and the type implement you have will determine what length will be necessary and to make it not interfere with the implement design and function. On these 2 1/2 inch square pieces, you'll need to mark the halfway point and drill a thru hole that goes through the front and back. The diameter of this hole will need to be sized to the diameter of the hitch pin that will secure the 2 inch square tubing to the 2 1/2 inch square piece.
    The 2 1/2 inch square tubing is welded vertically to the implement. You'll need appropriate sized and type wheels that can handle the weight of your implement.

    Next, you'll need some 2 inch square tubing. With the wheels you've selected, you can determine what length to cut the 2 inch tubing by dry fitting it inside the welded piece of 2 1/2 inch tubing. What you'll need to do next is mark holes that need to be drilled in the top and bottom of the 2 inch square piece. These two holes will not be located on the same sides. The top thru hole will be for the hitch pin that'll slide through both pieces from front to back. It has to align with the hole in the 2 1/2 inch square piece. The bottom hole is for a bolt to hold the wheel. This hole will be 90 degrees to the top hole. You could substitute the bolt for a piece of solid round stock and weld or fasten it with spring pins or cottor pins.


    In order to install the wheel and the pieces of tubing, the implement will need to be raised off the floor or ground. This method allows for quick removal of the wheels if needed.

    Had to use someone else's drawing to illustrate the idea. You may need to adjust the design to fit your specific implement or use.



    Attached Thumbnails Attached Thumbnails drawing.jpg  
    Last edited by green and red man; 01-26-2013 at 06:10 PM. Reason: added picture
    Ultrapile likes this.

  2. The Following User Says Thank You to green and red man For This Useful Post:

    Ultrapile (03-09-2014)

  3. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

Similar Threads

  1. Roll Over Limits for 1026R
    By Carvel Loafer in forum Sub Compact Utility Tractors (SCUT)
    Replies: 3
    Last Post: 07-04-2012, 12:33 PM
  2. Pull behind implements on a 3-point
    By RRMCCABE in forum Implements & Attachments
    Replies: 0
    Last Post: 02-12-2012, 06:12 PM
  3. Implements for 1 Series Tractors
    By Joe in forum Sub Compact Utility Tractors (SCUT)
    Replies: 0
    Last Post: 02-07-2012, 12:01 PM
  4. What implements are available for the 1026r
    By hopkinsmw in forum Sub Compact Utility Tractors (SCUT)
    Replies: 7
    Last Post: 10-25-2011, 07:38 AM
  5. Make way for Turtles!
    By eepete in forum Off Topic
    Replies: 6
    Last Post: 06-05-2011, 09:14 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •