Install 12 volt Receptacle in 4052M
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 12
Like Tree1Likes

Thread: Install 12 volt Receptacle in 4052M

  1. Top | #1

    Join Date
    Feb 2017
    Last Online
    10-08-2019 @ 08:24 AM
    Location
    Crandon, WI
    Posts
    13
    Thanks
    0
    Thanked 2 Times in 2 Posts

    Install 12 volt Receptacle in 4052M

    I purchased JD kit #AM136716, which is the 12v receptacle addition. However, I'm not entirely sure where to route or connect the wiring harness to in order to get 12v at the plug in the OEM stock location ? It doesn't have to be wired on/off with ignition as I'm only using it for a 12v 3pt 40gallon sprayer. Thanks in advance.

  2. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

  3. Top | #2

    Join Date
    Feb 2017
    Last Online
    10-08-2019 @ 08:24 AM
    Location
    Crandon, WI
    Posts
    13
    Thanks
    0
    Thanked 2 Times in 2 Posts
    Looking around for a 12v power source I have a number of open plugs, however, not sure if they're 12v or not ? The part I ordered (AM136443) comes OEM on the 4052R open station tractor. Trying to figure out how to power it. I do have a rear utility light on the ROPS that is switched on at the dash. Need input from the smarter people here. See attachments.
    Attached Thumbnails Attached Thumbnails 20190805_112901_1565023063010.jpg   20190805_112552_1565023095109.jpg   20190805_112504_1565023129392.jpg   20190805_112340_1565023161013.jpg   20190805_112153_1565023183483.jpg  


  4. Top | #3
    JDLTG's Avatar
    Join Date
    Jul 2019
    Last Online
    Yesterday @ 10:40 PM
    Location
    Mid-Willamette Valley Oregon
    Posts
    113
    Thanks
    22
    Thanked 14 Times in 8 Posts
    I just bought a 4044R a month ago. I plan to use the 12v outlet to power a sprayer too. What I found is the outlet was hot all the time if the ignition was on or off. I purchased an on/off rocker switch from JD and put it in the last position next to the 12v outlet so I could turn the sprayer on or off as needed. I cut the red wire and ran it through the switch.

    As short as the leads are, it must connect within the wiring harness under the switch plate on the fender. The switch plate is bolted on with the 2 bolts that are visible in your picture plus one in the cup holder. There are nuts underneath. Then you can lift the switch plate assembly up from the fender. I’d open up the harness carefully and see if you can find it and a place to screw the black ground wire to. Use a digital or analog voltmeter to check any available connections. You may also have to add a fuse to the fuse box. It might be worth asking the service dept for a little guidance too. Most are willing to guide you through it and the worse they could say is bring it in.
    Last edited by JDLTG; 08-05-2019 at 03:57 PM.
    Lee

    2018 JD 4044R/440R loader, 1939 JD model B, 2016 JD X380, 2017 JD X570 mowers. JD 503 brush mower, Frontier GM1060E finish mower, Frontier WC1105 wood chipper, JD 655 tiller. Cyclone Rake XL, Cyclone Rake Nut Rake, Misc discs and cultivators.

  5. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

  6. Top | #4

    Join Date
    Feb 2017
    Last Online
    10-08-2019 @ 08:24 AM
    Location
    Crandon, WI
    Posts
    13
    Thanks
    0
    Thanked 2 Times in 2 Posts
    There are a number of "plugs" underneath the right console; cruise control etc.....nothing to tie in the red & black wires for the 12v outlet. Still looking.......will enquire with my nearest JD dealer.
    JDLTG likes this.

  7. Top | #5

    Join Date
    Apr 2018
    Last Online
    10-14-2019 @ 01:08 PM
    Location
    Lumberton, Texas
    Posts
    7
    Thanks
    1
    Thanked 1 Time in 1 Post
    Did you figure it out? Please keep us informed, I am wanting to do the same thing on my 4052M.
    4052M - PowrReverser - 3rd, 4th and 5th SCVs. Frontier Grapple

  8. Top | #6

    Join Date
    Feb 2017
    Last Online
    10-08-2019 @ 08:24 AM
    Location
    Crandon, WI
    Posts
    13
    Thanks
    0
    Thanked 2 Times in 2 Posts
    I tied into the red and black wires under the right console which are 12v accessories using t-connectors; I then looked at the fuse box and noticed that JD didn't put any fuse connectors for that circuit in the fuse slot.......still working on it.

  9. Top | #7
    Jet Dr.'s Avatar
    Join Date
    May 2018
    Last Online
    11-11-2019 @ 08:01 AM
    Location
    Ridgeland SC
    Posts
    248
    Thanks
    11
    Thanked 15 Times in 14 Posts
    I've been looking at this. Does not help your situation on where to obtain power from, but will add two USB charging ports and a voltmeter.

    https://www.amazon.com/Rydonair-Univ...3M6FSYHMAQB497

    Jeff
    2018 3046R - Deluxe Cab, air ride seat, R4 tires, 3rd ESCV, diverter valve with 4th and 5th SCV's, mid PTO, 72D autoconnect MMM with independent lift, power beyond, 375A backhoe, 320R loader with 3rd function lines, L&R external mirrors, Frontier 60" 4 in 1 bucket and factory stereo with dedicated Sirius tuner.

  10. Top | #8

    Join Date
    Feb 2017
    Last Online
    10-08-2019 @ 08:24 AM
    Location
    Crandon, WI
    Posts
    13
    Thanks
    0
    Thanked 2 Times in 2 Posts
    Thanks.....will look into it after I find power.

  11. Top | #9

    Join Date
    Apr 2018
    Last Online
    10-14-2019 @ 01:08 PM
    Location
    Lumberton, Texas
    Posts
    7
    Thanks
    1
    Thanked 1 Time in 1 Post
    Did you finish the installation?
    4052M - PowrReverser - 3rd, 4th and 5th SCVs. Frontier Grapple

  12. Top | #10

    Join Date
    Feb 2017
    Last Online
    10-08-2019 @ 08:24 AM
    Location
    Crandon, WI
    Posts
    13
    Thanks
    0
    Thanked 2 Times in 2 Posts
    Yes, yesterday I located a 12v lead to my rear facing accessory light and using t-taps (2) I drew power from that source which is also switched on/off with the dash switch. I should've done that first rather than talked to the JD rep, although they didn't know that the accessory wires in the right fender didn't have any connection with the OEM fuse block. Fimco makes an alligator to 12v plug adapter to run a rear 40 gallon sprayer. Success, thanks for everyone's input.

  13. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

Page 1 of 2 1 2 LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •