Will a JD 40 loader fit 2016 x738
Results 1 to 5 of 5

Thread: Will a JD 40 loader fit 2016 x738

  1. Top | #1

    Join Date
    Nov 2016
    Last Online
    Yesterday @ 10:07 PM
    Location
    Southeast Nebraska
    Posts
    190
    Thanks
    54
    Thanked 9 Times in 4 Posts

    Will a JD 40 loader fit 2016 x738

    Someone is selling at JD 40 loader. In the add it says it fits JD 425,445,455. Just wondering it will fit my 2016 x738?

  2. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

  3. Top | #2
    tj1
    tj1 is offline
    tj1's Avatar
    Join Date
    Jan 2015
    Last Online
    09-18-2019 @ 07:50 AM
    Location
    ma
    Posts
    3,875
    Thanks
    266
    Thanked 304 Times in 227 Posts
    Quote Originally Posted by ultra7350 View Post
    Someone is selling at JD 40 loader. In the add it says it fits JD 425,445,455. Just wondering it will fit my 2016 x738?
    I don't believe you can have a loader on a 2016 X738.. I have a 2015 X738 and I Know I cannot adapt one on mine. Check the JD site to make sure.
    Jeff

    X 738 4X4/ 54" mower deck, 47" two stage snow thrower/ linear actuator spout control, Curtis hard side cab/heater, JD roof top LED work lights, Curtis fuse block, rear roof light connected to dash light switch and reverse lights, additional 20amp alternator, Curtis fast Cast 2000 sander custom fitted to tractor/ vibrator for use with dry sand, Kubota L39 TLB, JD 450 E dozer, Husky 18 horse/ 48" mower deck/Berco 42" two stage snow thrower/Berco soft side cab, Kubota RTV500-H.

  4. Top | #3
    TJR345's Avatar
    Join Date
    Jan 2016
    Last Online
    Yesterday @ 09:33 PM
    Location
    Area 51 in Cambria,NY
    Posts
    3,754
    Thanks
    415
    Thanked 479 Times in 370 Posts
    I would think not,the loader arms aren't wide enough for the newer tractors.CTC makes loaders for the newer x7xx series.
    Tom

    2019 X590 with power mulch control and PF bagger
    30" mechanical tiller
    02 X595 with 62" deck,front thatcher and powerflow PTO kit
    3pt hitch with Heavy Hitch 45 JD loader
    12 JD suitcase weights
    JD/Brinly 3pt plow
    Frontier SS1036 3pt pto spreader
    (2) JS63C walk behind mowers
    TS 105 JD weed wacker
    tow behind 15 gal. sprayer
    Turftime 60" lawn roller
    Turftime 54" 3pt core aerator

  5. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

  6. Top | #4
    sponfit's Avatar
    Join Date
    Apr 2016
    Last Online
    08-30-2019 @ 07:11 PM
    Location
    bakersfield ca
    Posts
    11
    Thanks
    1
    Thanked 0 Times in 0 Posts
    At a minimum, you'd have to build a new subframe.

  7. Top | #5
    Sergeant's Avatar
    Join Date
    Aug 2011
    Last Online
    Yesterday @ 04:30 PM
    Location
    Kane County,IL
    Posts
    1,138
    Thanks
    1
    Thanked 210 Times in 169 Posts
    Yes a 40 loader could be adapted to a X700 signature series easier than a 45 Loader though JBible on MTF has already adapted the 45 loader to his X738 Another 45 Loader Tale - MyTractorForum.com - The Friendliest Tractor Forum and Best Place for Tractor Information

    Let me go back to 2003. In early 2003 I was going to Buy a X465 2WD air cooled. Deere stated the 45 Loader did not work on the X465 do to the fact the 45 loader sub frame Interfered with cooling on the air cooled engine. Deere world Wide Told me a 40 loader from the 425 thru 455 would fit on the X465 because the 40 loader sub frame would not interfere with cooling on the X465 air cooled tractor. But I ended up wanting a little more Capable Loader so I went with a X485 with a 45 loader.

    For the Most Part the X700 signature series frame is the same as a X465's frame. Though the signature frame is thinner in key areas and doesn't have the Loader sub frame pass through holes. But that besides the point. Length and width of the frame are the same. Now You might have to drill some Holes In your frame to get it to work right. Or You could build a different sub frame sort of following what JBible did for his 45 loader in the Link above

    But the CTC loader would be a a faster and Not require any hole new hole Put In your frame and fits all X700 signature series tractors 2013 till present
    2013 John deere x ultimate

    When the X700 signature series was first thought up Deere had planned to do a new loader for the Signature Series That would have had a sub frame similar to the 40 loader. But the bean counters nixed the Idea( Nixing the loader had nothing to Do with the need for ROPS as some think)

    The ROPS was do to weight and new government regulations. So Deere didn't think ROPS would go over very well on the X700 series in North America. So the the weight was dropped for the Signature series so they wouldn't have to put ROPS on there Super Garden tractors

    BTW I had a 425 with a 40 loader when I bought the X485. Dealer was all set to move the 40 loader over to the X465 they had in stock. But I changed my mind at the last minute and went with the X485 with 45 loader.

    Attached Thumbnails Attached Thumbnails 2013_X_Model_006.jpg   2013_X_Model_007.jpg   2013_X_Model_009.jpg   2013_X_Model_008.jpg   2013_X_Model_011.jpg  

    Last edited by Sergeant; 11-20-2018 at 08:45 PM.
    John Deere Models: 2025RTLB(Gen 2),X748,GX335,140H3,112SF,110RF,Sabre 1542,TX Gator
    Cub Cadet Models:0riginal,70,106,XT3GSX & Experimental Non Production Rear engine rider
    Ingersoll Model:3016PS
    Simplicity Models:Wonder Boy
    White Model: GT2055

    MSGT 11 & 18 Series Retired

  8. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •