2038r error code and regen question
Results 1 to 9 of 9
Like Tree17Likes
  • 1 Post By Big
  • 4 Post By Herminator
  • 1 Post By cin769
  • 4 Post By HomesteadJoe
  • 4 Post By mike01
  • 3 Post By ddinham

Thread: 2038r error code and regen question

  1. Top | #1

    Join Date
    Nov 2014
    Last Online
    Today @ 10:16 AM
    Location
    SE Iowa
    Posts
    215
    Thanks
    2
    Thanked 2 Times in 2 Posts

    2038r error code and regen question

    Ok tractor has 122 hours on it and regen started,, took 4 hours to get over, first time I shut it off at 2 hours cause I was leaving and asked dealer about it and they said it could take that long so next day I fired it up and took another 2 hours then idled down.today went to move it the soot thing is on display says ecu has wrench and 3719.16 soot level reads 77% exhaust filter says 32
    Any ideas?
    Thanks

  2. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

  3. Top | #2
    ddinham's Avatar
    Join Date
    May 2013
    Last Online
    Today @ 02:17 PM
    Location
    Eastern Kansas
    Posts
    3,665
    Thanks
    167
    Thanked 504 Times in 387 Posts
    I would say it was because you shut it down during the regen, but I did that once quite some time ago and it was no problem when I restarted it. I have never had one that run anywhere that long. I think maybe a half hour or a little longer was the longest I have had in my over 600 hours. I think it is time to get with your dealer.

    Dave
    JD 4066R CAB
    JD H180 FEL with SSQA brackets, JD iMatch, JD Ballast Box & ext, JD pull behind seed spreader
    Frontier RB2196H 8 ft rear blade/hyd angle, Frontier BB1065 Box Blade, Befco 3pt 110 inch RFM
    48" pallet forks, KK 3pt Boom Pole, Northern Tool 3pt middle buster, 2 bottom Dearborn plow
    County Line post hole digger, Rhino 3pt 10ft brush hog, Land Pride 8ft rock rake
    Fit Rite Hydraulics 3pt Top Link, front 3pt adapter for SSQA, 7 1/2 ft Field Roller, 8ft Dearborn tandem disk

  4. Top | #3
    Big
    Big is online now
    Big's Avatar
    Join Date
    Jan 2018
    Last Online
    Today @ 02:45 PM
    Location
    Greenville SC
    Posts
    1,347
    Thanks
    110
    Thanked 245 Times in 176 Posts
    No way a Regen should take 4hrs. I have been through a couple and I'd say 30 min tops. I was mowing grass both times and noticed the light and kept on mowing. After a while 20-30 mins it was finished. Never timed it, but 4hrs! If you had a half a tank you'd run out of fuel. Dealer definitely needs to check this out.

    Edit:Make sure to read your manual on regens. There is a minimum rpm you need to have for it to work.
    Last edited by Big; 07-27-2019 at 11:03 PM.
    bvbearcat likes this.
    -2017 2032R, 220r Loader, I-Match, Ken's Extended Top Hook, MMM, JD Ballast Box, Dual rear SCV's, Single Point Hydraulic Connection, Landscape Rake, Tarter Tiller, Boom Pole, Middle Buster/Potato Plow, Drag Harrow, Single Row Hipper, 5' Enorossi sickle bar, 3 point spike drag, Titan 42" Forks, 60" Box Blade, Landpride 3 point spreader, Leinbach 5' Disc.

    -Bobcat 325G Mini Ex
    -Toro Dingo 322 with many attachments
    -Honda Pioneer 700

  5. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

  6. Top | #4
    Herminator's Avatar
    Join Date
    Mar 2017
    Last Online
    Today @ 11:48 AM
    Location
    Northern Illinois
    Posts
    4,167
    Thanks
    1,816
    Thanked 891 Times in 671 Posts
    Mine always seem to happen when I am about to finish working or doing light work.

    I usually put the throttle around 2000 and let it sit or do the light work at 2000.. Again half hour tops.
    Welcome to Intermission.

    2017 2038R, 400, 3020 & HPX and thingies to hook to the them.
    112 - Sold in July 2017 but took me until November to admit I just cast it out into this cruel world.
    #compactfarmer

  7. Top | #5

    Join Date
    Nov 2014
    Last Online
    Today @ 10:16 AM
    Location
    SE Iowa
    Posts
    215
    Thanks
    2
    Thanked 2 Times in 2 Posts
    I thought it automatically set the idle I've never raised it I'll read on that today
    greenharley likes this.

  8. Top | #6
    HomesteadJoe's Avatar
    Join Date
    Mar 2017
    Last Online
    Yesterday @ 02:57 PM
    Location
    Southwestern Connecticut
    Posts
    1,603
    Thanks
    139
    Thanked 284 Times in 206 Posts
    My 2038R has about 440 hours on it and it has gone through quite a number of regens as you can imagine. If a regen is in process when I am done with using the tractor, I simply select the regen STOP button, and let the tractor cool down and shut it down. The regen automatically restarts the next time the tractor is used and the RPM hits 1500. No need to run the tractor just for regen. It's a terrible waste of yours and the tractor's engine running time......Also, in my experience, increasing the engine RPM also helps shorten the time it takes to perform the regen, although I can't swear to this.... I've never actually timed it.

    Sincerely
    BadAss 2038R, R3s, R4s, Spacers, Eng & Tranny Heaters, LEDs, Cages, Fender Flares, Front Fenders, iMatch, Heavy Hitch, Hitch-N-Can, 800# Quick Tach Weights, 220R Loader, Single Point Hyd, 57" HD Bucket, WR Long Tooth Bar & 3rd Function Hyd, 55" Wicked Root Rake Grapple, 270B Backhoe, 72D MMM, Front 3 pt Hitch, 366 FMB Blade, PHD300 Post Hole Digger w\ Auger Set, LR2172 Landscape Rake w/gage Wheels, RB2072 Rear Blade, BB2072 Box Blade, AP12F Pallet Forks, EA 72" Pine Needle Rake, Fit-Rite TNT

  9. The Following User Says Thank You to HomesteadJoe For This Useful Post:

    Herminator (07-29-2019)

  10. Top | #7
    mike01's Avatar
    Join Date
    Mar 2017
    Last Online
    Today @ 09:41 AM
    Location
    NY
    Posts
    1,273
    Thanks
    34
    Thanked 163 Times in 105 Posts
    I’ve done two parked regens in about 70 hours. The first was just to see what it was like. The second was because the soot level was at almost 70% and I like to get it over with so I don’t have to worry about it. Both times took about 20 minutes.

    I had one come on while brush hogging. I had no idea it was happening and it lowered the soot about 15 percentage points.

    Most of what I do is in short spurts. The only exception is snow blowing and brush hogging, so my soot builds up quickly.

    If yours is going on for hours, something is wrong. Tell the dealer to fix it.

    I really hate the DPF.
    2019 X758, 54" Autoconnect deck
    2018 2032R, 220R Loader, dual rear SCV, hydraulic top link, SB1164 Snow Blower, RC2072 rotary cutter, BB5048L box blade, 42" Titan forks, BB2060L back blade

    Owned in the past:
    X570, X758 (2015), 1025R, X590

  11. Top | #8
    ddinham's Avatar
    Join Date
    May 2013
    Last Online
    Today @ 02:17 PM
    Location
    Eastern Kansas
    Posts
    3,665
    Thanks
    167
    Thanked 504 Times in 387 Posts
    Quote Originally Posted by cin769 View Post
    I thought it automatically set the idle I've never raised it I'll read on that today

    It will not automatically set the idle, unless you have already exceeded 1500 rpm, then it will not allow it to be less than 1500 rpm. You will get a msg on the display that you need to increase the rpm if it is less than 1500 when the regen starts.

    Dave
    greenharley, Herminator and Big like this.
    JD 4066R CAB
    JD H180 FEL with SSQA brackets, JD iMatch, JD Ballast Box & ext, JD pull behind seed spreader
    Frontier RB2196H 8 ft rear blade/hyd angle, Frontier BB1065 Box Blade, Befco 3pt 110 inch RFM
    48" pallet forks, KK 3pt Boom Pole, Northern Tool 3pt middle buster, 2 bottom Dearborn plow
    County Line post hole digger, Rhino 3pt 10ft brush hog, Land Pride 8ft rock rake
    Fit Rite Hydraulics 3pt Top Link, front 3pt adapter for SSQA, 7 1/2 ft Field Roller, 8ft Dearborn tandem disk

  12. Top | #9
    Kingnuke32's Avatar
    Join Date
    Jan 2017
    Last Online
    Yesterday @ 03:06 PM
    Location
    PA
    Posts
    200
    Thanks
    16
    Thanked 104 Times in 34 Posts
    3 regens on my 2038R in 200 hours, 20-30 minutes each, if you are not over 1500 RPM's it will give you a message to increase RPM's, I mow with mine so running it at WOT cuts down on the number of regens.
    2017 2038R, 72" MMM, 220R Loader, 60" Frontier Box Blade, Land pride Rotary Spreader, 59" JD Snowblower, 60" KK Tiller, 60" KK rotary cutter, Artillian Forks, KK Carry All.

  13. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •