OMNI Carry All and Draw Bar Hitch
Results 1 to 6 of 6
Like Tree2Likes
  • 1 Post By psrumors
  • 1 Post By 636mullet

Thread: OMNI Carry All and Draw Bar Hitch

  1. Top | #1
    mjarmstr's Avatar
    Join Date
    Sep 2014
    Last Online
    10-22-2018 @ 09:10 PM
    Location
    Iowa
    Posts
    238
    Thanks
    11
    Thanked 21 Times in 19 Posts

    OMNI Carry All and Draw Bar Hitch

    I've seen plenty of people on here like the ONMI Manufacturing Carry All and I'm thinking about ordering one for my 1025R, however I have a couple of questions that I haven't been able to figure out.

    It looks like a lot of people have the carry all on a Transformer with or without weight rack and many with a quick hitch setup. I already have a cross draw bar on my 3-point so I was looking at getting the Heavy Duty Combo Draw Bar Trailer Hitch to use with the carry all. My concern is that it looks like all of the other hitches offset the middle of the carry all a few inches from the lower link arms. With the draw bar hitch the carry all would be centered directly over my draw bar and I'm concerned it is going to hit the toolbox.

    Also I'm considering getting the version with both the vertical and horizontal mounting options so I could possibly use it on my vehicle or on the lower position of the combo hitch. My concern here is a again a matter of clearance. In the lower position using the horizontal mount, is the vertical mount doing to stick down too far and end up dragging on the ground when I have the 3-point down?

  2. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

  3. Top | #2

    Join Date
    Aug 2013
    Last Online
    09-13-2019 @ 09:18 PM
    Location
    Cartersville (NW) GA
    Posts
    2,379
    Thanks
    103
    Thanked 365 Times in 267 Posts
    Excellent questions, I wish I had answer for you. Omni is very nice to sea with, drop them an email and I bet they get back to you real quick.


    DRobinson likes this.
    1025r TLB w 60D MMM & Independent Lift
    SN 114287 Built April '13 received 8/21/13
    180 degree thermostat
    Omni Transformer w/ integrated weight bracket
    Single Point
    Ken's Bolt on hooks
    Artillian Forks (42")
    Full Compliment of Wheel Weights (340lbs)
    Custom Seat Springs

    Kubota 326H 72" deck ZTR

    Stihl MS361, FS250R

  4. The Following User Says Thank You to psrumors For This Useful Post:

    obee1kubota (10-02-2014)

  5. Top | #3
    636mullet's Avatar
    Join Date
    May 2012
    Last Online
    05-14-2019 @ 07:05 AM
    Location
    Council Bluffs, IA
    Posts
    1,626
    Thanks
    127
    Thanked 188 Times in 170 Posts
    If you have your carry all "Level" then it will come close to the toolbox but it will clear. I put my FIMCO sprayer in it and spray my yard. When I ordered mine I didn't get the side screens and I wish I had. My Transformer is pretty awesome. It's on all the time.





    -636
    Gizmo2 likes this.
    Early 2012 1026R with H120 and 60" auto connect MMM

  6. The Following 2 Users Say Thank You to 636mullet For This Useful Post:

    mjarmstr (09-25-2014), obee1kubota (10-02-2014)

  7. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

  8. Top | #4
    636mullet's Avatar
    Join Date
    May 2012
    Last Online
    05-14-2019 @ 07:05 AM
    Location
    Council Bluffs, IA
    Posts
    1,626
    Thanks
    127
    Thanked 188 Times in 170 Posts
    Click image for larger version. 

Name:	uploadfromtaptalk1411669354916.jpg 
Views:	60 
Size:	71.7 KB 
ID:	33140
    Here it is with my sprayer mounted.
    Early 2012 1026R with H120 and 60" auto connect MMM

  9. The Following User Says Thank You to 636mullet For This Useful Post:

    obee1kubota (10-02-2014)

  10. Top | #5
    mjarmstr's Avatar
    Join Date
    Sep 2014
    Last Online
    10-22-2018 @ 09:10 PM
    Location
    Iowa
    Posts
    238
    Thanks
    11
    Thanked 21 Times in 19 Posts
    psrumors - I did email omni and he said the draw hitch would work, but wasn't sure about hitting the toolbox. He said to measure about 10 inches from the middle of the lower link arms. When I measured that it puts it right at the edge of the toolbox which is part of why I posted.

    636mullet - Looking at your pictures I think that it would hit the toolbox with the draw bar hitch based on how tight yours looks with the transformer. I also see you got both the horizontal and vertical mounting options. Have you used the horizontal one? Have any issues with the vertical portion dragging in that configuration?

  11. Top | #6
    636mullet's Avatar
    Join Date
    May 2012
    Last Online
    05-14-2019 @ 07:05 AM
    Location
    Council Bluffs, IA
    Posts
    1,626
    Thanks
    127
    Thanked 188 Times in 170 Posts
    If you have your top link cranked all the way in I believe the CarryAll will hit the tool box. If it's leveled then it clears no problem. I haven't used the Horizontal mount other than one time to see how it looked. In uneven situations I could see the vertical post hitting, but with the CarryAll all the way up I don't see that to be much of an issue unless things are really steep. I'll try and snap some pictures tomorrow.

    -636
    Early 2012 1026R with H120 and 60" auto connect MMM

  12. The Following User Says Thank You to 636mullet For This Useful Post:

    obee1kubota (10-02-2014)

  13. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •