1025R Hydraulic Leak
Results 1 to 7 of 7
Like Tree3Likes
  • 3 Post By 56Nine

Thread: 1025R Hydraulic Leak

  1. Top | #1

    Join Date
    Aug 2015
    Last Online
    08-09-2016 @ 02:25 PM
    Location
    Kentucky
    Posts
    7
    Thanks
    0
    Thanked 0 Times in 0 Posts

    1025R Hydraulic Leak

    Every time I disconnect my front loader I lose a lot of hydraulic fluid from the loader.

    Is this normal? What can I do to prevent?

  2. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

  3. Top | #2
    56Nine's Avatar
    Join Date
    May 2015
    Last Online
    Today @ 08:31 AM
    Location
    Alleman, IA United States
    Posts
    707
    Thanks
    30
    Thanked 212 Times in 116 Posts
    Quote Originally Posted by Rick1025r View Post
    Every time I disconnect my front loader I lose a lot of hydraulic fluid from the loader.

    Is this normal? What can I do to prevent?
    Maybe we could start with you describing your disconnect procedures.

    When I disconnect, after the loader is physically free from the tractor, I shut it off, wiggle the control in all directions then disconnect the hydraulic lines starting with the top left, top right then lower left, lower right.

    I lose "a little" meaning MAYBE a teaspoon or less each time, certainly not "a lot". Can you estimate what you call "a lot"?
    RandyM, dieselshadow and Ray_PA like this.
    Darwin
    1025r -> 60D Auto Connect MMM; H120 FEL, 53" bucket, KBOH (3), shackle backer (3), bolt on replaceable cutter; Frontier SB1154; 5' king cutter box blade; king cutter 3pt trailer mover; JD ballast box; 1.25" rear wheel spacers, 40 gallon Fimco sprayer, 52" Ohio Steel lawn sweeper, 3pt King Kutter Poly Fertilizer spreader.

  4. Top | #3

    Join Date
    Jan 2016
    Last Online
    10-12-2019 @ 04:46 PM
    Location
    Northern Viriginia
    Posts
    223
    Thanks
    27
    Thanked 26 Times in 22 Posts
    A few drops is the most I will ever get on disconnect.
    2015 1025R w/ H120 Loader, 60D MMM AutoConnect, 54" QH Snowblower & Titan Pallet Forks

  5. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

  6. Top | #4
    Drifterbike's Avatar
    Join Date
    Jul 2015
    Last Online
    10-09-2019 @ 09:36 AM
    Location
    Hampton Ill
    Posts
    2,713
    Thanks
    1,084
    Thanked 317 Times in 278 Posts
    Today when the John Deere driver dropped of my 1025Rl we put the loader on and off three times and just got a drop out each time. He used a paper towel and non Got on the floor. We shut the tractor then cycled the loader control several times to take the pressure off and just got a few drops in the paper towel.

  7. Top | #5
    96PSD's Avatar
    Join Date
    Jul 2014
    Last Online
    10-11-2019 @ 10:21 AM
    Location
    East Windsor, NJ
    Posts
    445
    Thanks
    15
    Thanked 60 Times in 43 Posts
    One of the important things to do before disconnecting your wet lines after you have "parked your loader off from the tractor" is to rotate the loader joystick in all directions to take the pressure off the lines and sump back into the tractor as much as possible. Especially if you do it in cooler weather and then try and reattach it when it is warmer outside. You may have to resort to this if you can not re-connect the lines. Amazing how much pressure builds up in the loader lines, get a plastic baggie out and paper towels and a small hammer to pop the ball bearing to release the built up pressure to connect your lines back up.
    2014- JD 1025r
    L120 59" FEL, 260 BH, 60D MMM
    66"/54" plow with Artillian extension and rubber edge
    Artillian 36" forks
    JD 550 3PT Tiller
    54" spike aerator
    Fimco 3PT 40 gal boom sprayer
    Trac-Vac 580
    CMP 3PT 60" Dethatcher
    51" Lucknow 3PT rear snowblower
    Omni Transformer 3PT weight rack w/ 2" hitch receiver 6-42lbs weights

  8. Top | #6

    Join Date
    Feb 2014
    Last Online
    10-10-2019 @ 12:21 AM
    Location
    Minnesota
    Posts
    374
    Thanks
    22
    Thanked 148 Times in 77 Posts
    I really only get a couple of drops out of my loader hydraulic connections during a disconnect and I rarely get any during a reconnect. The power beyond (for the backhoe) is a different story. I'll usually get a half teaspoon worth of hydraulic fluid that will spill out when I'm swapping the connection.

    The only time it concerns me is when I'm out of paper towels and don't have a rag handy.

  9. Top | #7

    Join Date
    Nov 2015
    Last Online
    09-29-2019 @ 04:10 PM
    Location
    Maryland
    Posts
    52
    Thanks
    1
    Thanked 2 Times in 1 Post
    My loader is doing the same thing on my 1025r. My dealer is coming out next to put on new quick disconnects the male ends to see if that corrects the problems. Its like the ball value does not fully close once the hose is disconnected.
    2016 1025R TLB 60D autoconnect mower, and 2048 rotary cutter, ballast box, and iMatch quick hitch

    2015 GMC SLT 2500HD with Duramax / Allison tranny

  10. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •