Electric Terminal Question
Results 1 to 4 of 4
Like Tree4Likes
  • 4 Post By keane

Thread: Electric Terminal Question

  1. Top | #1

    Join Date
    Jan 2017
    Last Online
    04-25-2017 @ 09:06 PM
    Location
    Missouri
    Posts
    6
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Electric Terminal Question

    Okay my first question about my 1023E ....Adding some front and rear lights and have the need for the electric terminal that goes into the back of fuse block so you can slide fuse in from the front . Will try to attach photo

    Thanks for the Help.
    Attached Thumbnails Attached Thumbnails Terminal1.jpg  

  2. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

  3. Top | #2

    Join Date
    Jul 2014
    Last Online
    Yesterday @ 10:34 PM
    Location
    Northern Colorado
    Posts
    919
    Thanks
    533
    Thanked 372 Times in 195 Posts
    Check this post. LINK HERE

    I think it has the information you are looking for.

    Keane
    1025R SCUT
    H120 FEL
    260 Backhoe
    54D MMM
    54 Snow Blower
    54 Front Blade
    JD I-match
    10P Dump Cart
    Heavy Hitch: Receiver hitch w/rack, 2" receiver 8-Weight Rack, 2" front & rear receivers, synthetic blade
    Ken's BOGH: Grab Hooks/ Clevis Mounts, Oblong Ring Slings, Differential Pedal, backhoe step, etc.
    Everything Attachments: Pine Needle Rake, Aerator
    Bxpanded: Ripper Claw, Trenching Bucket, Quick Change for 260 BH
    Artillian: 3K fork frame & 36" tines
    Miller Tire: R4 tire chains

  4. The Following User Says Thank You to keane For This Useful Post:

    jbfrancis3 (02-27-2017)

  5. Top | #3

    Join Date
    Jan 2017
    Last Online
    04-25-2017 @ 09:06 PM
    Location
    Missouri
    Posts
    6
    Thanks
    0
    Thanked 0 Times in 0 Posts
    THANK YOU.....That thread did help and will go from there.

  6. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

  7. Top | #4

    Join Date
    Jul 2014
    Last Online
    Yesterday @ 10:34 PM
    Location
    Northern Colorado
    Posts
    919
    Thanks
    533
    Thanked 372 Times in 195 Posts
    In the solution posted in the linked thread, the author says you must use a crimp tool on the connector. If you are ultra-picky about doing everything the right way, he is right. And you will find those crimp tools can be very expensive. And you many only use it 2 or 3 times.

    I'm going to be making some similar connections very soon. I'm not going to buy the crimp tool.

    There are 3 sets of prongs on the end of the connector where the wire goes. The first set (nearest the connector's end) is used to grip the insulation. Strip the wire and make the stripped area just long enough to fit through the 3rd set of prongs. Don't make it too long or it may interfere with the fuse being inserted. Place the wire end into the trough on the connector with the insulation just past the first set of prongs. Using needle nose pliers, carefully bend each prong in the first set down onto the insulation. After the prongs are bent over the insulation, use the needle nose pliers to squeeze them tight into the insulation. Carefully arrange the bare wires down against the connector, then bend the 2nd and 3rd sets of tongs down into the wire. Gently squeeze each prong down into the bare wire.

    When the wire is mechanically connected to the connector, use a soldering iron designed for electronic work (and a high quality solder designated for electronic work) to solder the wire to the connector. Be careful not to use too much solder; you don't want it interfering with the fuse end of the connector. The heat will melt the insulation into the prongs. This wire will not be coming out of the connector for a long time.
    1025R SCUT
    H120 FEL
    260 Backhoe
    54D MMM
    54 Snow Blower
    54 Front Blade
    JD I-match
    10P Dump Cart
    Heavy Hitch: Receiver hitch w/rack, 2" receiver 8-Weight Rack, 2" front & rear receivers, synthetic blade
    Ken's BOGH: Grab Hooks/ Clevis Mounts, Oblong Ring Slings, Differential Pedal, backhoe step, etc.
    Everything Attachments: Pine Needle Rake, Aerator
    Bxpanded: Ripper Claw, Trenching Bucket, Quick Change for 260 BH
    Artillian: 3K fork frame & 36" tines
    Miller Tire: R4 tire chains

  8. Remove Advertisements
    GreenTractorTalk.com
    Advertisements
     

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •