Green Tractor Talk banner

Discussions Showcase Albums Media Media Comments Tags

1-19 of 19 Results
  1. Large Frame Compact Utility Tractors (LCUT)
    Total newb here. Was trying to push a little snow the other day with my 300cx loader. I am familiar with Kubota float function to the stick, just push it past full forward and the fel goes into float. my question is, how do you do this on the 3520? The FEL manual says see the tractor manual...
  2. Sub Compact Utility Tractors (SCUT)
    I was plowing the driveway this morning and all of a sudden I was unable to curl or dump the bucket. Looking under the rubber boot I found the broken piece. Wondering how difficult this is to repair or am I looking at a dealer visit? Purchased the 1025r new in spring 2019. Has almost 400 hours...
  3. Wanted to Buy
    I'm looking to purchase a John Deere 45 loader in good condition. I am located in the middle Tennessee area, but am open to paying shipping for the right loader.
  4. Implements & Attachments
    Hello everyone, Please help me pick the right loader for my x595. I have to decide by tomorrow. 1. MX C1 - made by a French company, seems to be doing good stuff. I need to go through a dealer to get it - and they proved to be very unknowing of this model. I expect it to cost around €3,5k and...
  5. Wanted to Buy
    Looking to purchase a Model 45 front end loader for my 2011 X700 ‘Ultimate’ series tractor. My tractor does have the cutout in the chassis for the cross bar frame mount. I know these 45’s are a bit hard to find. Any help or leads greatly appreciated. Although preferred, it does not need to...
  6. Implements & Attachments
    I have a 1025r with the loader, I have a half acre pond that has moss and vines that grow about 4 ft out from the bank, I usually just use a hard rake and rake it out by hand but I’ve been thinking about getting a piece of flat steel about as wide as the loader and welding 6ft pieces of rebar...
  7. Sub Compact Utility Tractors (SCUT)
    Good morning. Took delivery of my 1025R and my operators manual (Issue A9) doesn’t have any info on ballast weight. I have the quick release ballast box from the dealer. Couple questions: 1. Where do I find weight requirements? I will primarily be removing trees but also moving soil. 2. Is it...
  8. Medium Frame Compact Utility Tractors (MCUT)
    Hello all, I have been searching this forum and all of the google, and have been unable to get a clear answer. Here is what I have going on. Recently purchased a 1979 Model 850 tractor. it came with a brush hog, and that was the extent of it. On Monday, I was able to locate and purchase a...
  9. Hydraulics
    Hey ya'll first post here: I'm fixing a JD 4100 compact tractor for a friend that has a 410 loader. The loader was not lifting properly so I did the obvious and cleaned the suction screen, changed the filter and put new JD hydraulic oil in it. It seemed to work great...for a minute. Even before...
  10. Lawn & Garden Tractors
    Hey folks, I'm a city boy who bought an 18 acre property. I had logging done. The yard in front of my house is small, and there is a septic mound that is a bit steep, but can be managed. Other than that, I have 1500 feet of skid trails with grass and weeds that needs mowing. I also have a ton...
  11. 3039R

    This is my tractor sitting at the dealer when it first arrived. It was a Basic "R" model before any of the options were added. It received a H165 FEL, 72" MMM, John Deere Canopy and all the available optional Hydraulics
  12. Hydraulics
    I have a 3320 w/300CX and skid steer plate up front and I've always noticed that the bucket was a little crooked. I lived with it but now I need to use pallet forks on it and I can't have the mismatch of piston speed. I'm not sure what causes this. Dropping the bucket down, the left piston is...
  13. Large Frame Compact Utility Tractors (LCUT)
    I have a JD 3032E, I have installed the rear hydraulic remote Kit, went quite well. I want to ask if anybody knows what make the D160 loader valve is and is the rear remote the same make. I have looked all over for the manufacture of the valves and have found nothing. I wanting to install a...
  14. Utility Tractors
    Wondering if someone can help me out with parking stands for my 541 loader? I picked up a 5400 tractor in excellent shape and it came with a 541 loader. I used it this summer for hay baling and when I went to take off the loader I found to my dismay that there weren't any parking stands. I...
  15. New Member Introductions
    New member from Central Iowa. My wife and I moved from city to 6 acres in the country to a small farm that was once organic certified. We aren't sure what's next except a big garden, berries and fruit trees (and birds). Just got a 1025R with FEL, belly mower, rear blade, and based on advice I...
  16. Implements & Attachments
    I decided I needed a dolly to store my FEL. Space in my garage is limited and I sometimes have to move things around just to have room to work. Without a dolly, this requires the tractor every time. This fills the garage with diesel fumes and requires taking off other front-end implements to...
  17. Sub Compact Utility Tractors (SCUT)
    Hi experts! Ran my 1026r FEL for 4 hours yesterday removing about 10" deep of soil for a large brick patio. This was the most FEL work since I got the tractor and only have 13 hours on it. My limited experience question; when I dump the bucket of removed dirt and then move a bit forward, drop...
  18. Sub Compact Utility Tractors (SCUT)
    As a new 1026R owner, I have been looking for a way to move the 60D deck around once it is off the tractor, it is heavy. I have Ken's hooks on the bucket and can use chain but since all the implements will be living outdoors, I want to minimize scratching the paint off with chain. I went to...
  19. Hydraulics
    Just went to move my H120 FEL outside today to install Kenny's hooks on the bucket and I am not able to hook up the black and yellow quick connects. I push as hard as I can, but I cannot get the ring on the female portion of the connection to snap in place. I think I've isolated the problem...
1-19 of 19 Results
Top