Green Tractor Talk banner

hydraulics

  1. 1025r broke steering hydraulic line

    Sub Compact Utility Tractors (SCUT)
    I was clearing some brush yesterday with a grapple and the steering stopped working. I looked under the tractor and there was quite a bit of fluid and I found that a hydraulic line had been broken away from the steering cylinder on the front transaxle, I am assuming I lust have wedged it...
  2. Haying with my 955 Revisited, hydraulic questions

    Large Frame Compact Utility Tractors (LCUT)
    Ok I have installed the Enorossi mower on my 955, but it has challenged me with the hydraulic lift: the lift piston is a single hose and breather set up. The 955's rear ports for the backhoe might be fine with a valve kit, but I would think that I would have to modify the lift piston into a...
  3. 8295R Rear Lift Arm Not Holding Position

    Agricultural Tractors
    Have a 8295R (first 2 of last six of serial number is "09") and pulling a root plow. No prior problems. Have Upper limit and set point programmed. Moving forward, I notice the 3 point hitch lowering by itself. I can stop the bleed down by constantly adjusting the Rear Hitch Command Lever. No...
  4. Hydraulic Drain Plug on 6115D

    Utility Tractors
    Its time for me to change the hydraulic oil on my 6115D. There are a couple drain plugs on the underside that i need to remove. I have a T55 torx that seems to be about right, but i'd rather not strip it out. Is it a torx, or a some other special bit i need to get? I've searched all the...
  5. FEL Bucket tilt piston slow....

    Hydraulics
    I have a 3320 w/300CX and skid steer plate up front and I've always noticed that the bucket was a little crooked. I lived with it but now I need to use pallet forks on it and I can't have the mismatch of piston speed. I'm not sure what causes this. Dropping the bucket down, the left piston is...
  6. john deere 4020 hydraulic issue

    Agricultural Tractors
    i have a 1966 John Deere 4020 PS diesel the tractro starts easy and runs well. the hydraulics work in D only. if i select L or LD no hydraulics at all but in D the 3 point raises and lowers quickly. the FEL works if i manipulate the levers in a specific sequence (eg scv lever forward + loader...
  7. 4210 General Maintenance Info

    Large Frame Compact Utility Tractors (LCUT)
    I just bought a 2003 4210 in good general condition but with a few minor issues: No rear lights, flashers or turn signals; bucket curl cylinders leak down; hour meter not functioning; speed control not working. I can live with most of that till winter. Is there a site where I can get...
  8. Power Steering failing??

    Large Frame Compact Utility Tractors (LCUT)
    I recently acquired a 3520 with 1400 hours and while the power steering works fine, I noticed that the steering wheel slowly drifts counter clockwise. I hadn't noticed this working in the yard, but I had to drive it a couple miles on the road, and became obvious then. Maybe a whole rotation in...
  9. JD2630 independent pto pressure test

    Utility Tractors
    Hi all, I have a 1976 JD2630 with independent PTO. PTO will not disengage. Put gages on clutch controller test ports. rearward port pressure reads 140psi constant with PTO lever in both positions. Forward port pressure reads 0psi with PTO lever in both positions. Does this mean I need to...
  10. Running Rear Hydraulics to Front for Auxilliary on 5055e

    Utility Tractors
    Just recently bought a 5055e with 240 loader (quick attach model). Wondering if it's possible (and/or advisable) to run a line from the rear hydraulics to the front for things like a grapple, etc. Anyone have experience with this? What would an alternative be to get additional hydraulics to...
  11. Changing hydraulic fluid/filter

    Sub Compact Utility Tractors (SCUT)
    A few years ago my 1026R was due for its first 50hr service. I couldn't get the plug out. In fact I stripped it bad. Not wanting the mess with it, thinking this this first service was important, and having a bit of work to do that summer, I had the dealership come get it, service it, and...
  12. Custom Rear Dual SCV on 2520

    Medium Frame Compact Utility Tractors (MCUT)
    Greetings everyone. I started a project to add Power Beyond (PB) to my 2520. I reviewed the prior threads on PB and took their lead for the plumbing details (thanks). I added a little of my own twist - a dual control valve and a custom bracket. It's not complete at this point, but I...
  13. Hydraulic dump trailer/barge wagon

    Vintage Lawn & Garden Tractors
    First time posting here. I'm a transfer from wfm. This is a dump trailer barge wagon I just finished. I bought this last summer and the p.o. had done a pretty good job with the basics and I just took it a step further. He had designed it to be used behind a four wheeler and was using a small...
  14. JD 2130 No hydraulics unless PTO on

    Hydraulics
    Hi, was wondering if anyone out there could shed some light I am having with our old JD 2130. I’m not sure how many different variants there were, but ours is 2 WD and has 2 gear leavers (park-high-low-reverse) and 1-4 (I read somewhere some have a hydraulic high/low – ours definitely does...
  15. Need insight on a John Deere 870 purchase and tire options?

    Medium Frame Compact Utility Tractors (MCUT)
    Hey guys, I am looking at buying my first tractor for my landscaping business. I have stumbled across what seems to be a good deal but there are some drawbacks I need advice on. A residential client of mine has a mid 90s JD 870 that has been unused and kept for years under a garage breezeway...
  16. JD 2350 Hydraulic Hose connecting location I

    Agricultural Tractors
    I bought a 2350 with a front loader attachment , four hoses that go to the loader connect with quick couplers but 2 go from the gate valve and attach to the tractor somewhere and that is a hard diagram to find . If someone could help me out would be greatly appreciated . Thanks ledft
  17. changing old trans/hydraulic fluid over to Hy-gard in a 314

    Vintage Lawn & Garden Tractors
    Bought an early '80s 314 that is still running on the old pink hydraulic/transmission fluid. Recently had to repair one of the hoses coming off the charge pump, and lost a decent amount of fluid before I fixed it (it doesnt even show in the clear tube). I'm thinking this is a good time to just...
  18. 5520 Hydraulic Problems

    Utility Tractors
    Hi - I have a 2006 5520 with 5500 hours on it. It is the main tractor on my small dairy farm, and gets quite a lot of work. We make 4x4 round bales and use the 5520 for all hauling, moving bales, etc... For some time now I have been having significant problems with the hydraulic system...
  19. Just Bought My First Tractor!

    New Member Introductions
    I just bought a 2007 John Deere 3520 with a 300 CX loader and a 72" belly mower. It has about 800 hours and in great condition. I'm super excited about the new tractor but I also made a slight mistake by not putting pins in the ROPS while pulling in the garage. The ROPS brushed against the rear...
  20. Sticky hydraulic valve on 955 Rockshaft

    Large Frame Compact Utility Tractors (LCUT)
    A while ago I posted that my rockshaft arms had lowered themselves and would not raise up. I rebuilt the Rockshaft control valve assembly...everything worked for about 4-5 months until I ran the log splitter off the rear hydraulics again...it worked briefly right after I disconnected the...
Top