Green Tractor Talk banner
1 - 14 of 14 Posts

·
Administrator
Joined
·
23,165 Posts
Very cool, don't forget a link in the contest thread ;)

Did I miss the diverter install thread? :unknown:

PS. It look like you where pasting from MS Word? Some punctuation, particularly the ' is not recognized and everything gets cut off after it. If you need help modifying your post please PM me.
 

·
Registered
Joined
·
150 Posts
Discussion Starter · #4 ·
Diverter

Very cool, don't forget a link in the contest thread ;)

Did I miss the diverter install thread? :unknown:

PS. It look like you where pasting from MS Word? Some punctuation, particularly the ' is not recognized and everything gets cut off after it. If you need help modifying your post please PM me.
GRESEN DIVERTER VALVE
PN MS06 UDNA Green Motor vehicle Vehicle Auto part Tire
12B
Mfg. Parker PN 994450 Green Bicycle part Bicycle fork Bicycle wheel Vehicle
 

·
Registered
Joined
·
150 Posts
Discussion Starter · #6 ·
Joystick take 2

Pipe Auto part Fuel line

Auto part

Text Line Font Parallel Design


Joy Stick
Tubing, 1/2in Dia. X .049 wall thickness
2ea. 1/2 x 13 bolts machined to make end parts and Jam nuts.
1inch of 1/8 x 1/8 bar stock
5/16 washer bored to 1/2in ID for handle stop
JD handle Base, P/N M126552 $2.69 and Cap P/N M126553 $1.63
Push button switch used was Alco MPG 206R with weather boot seal
Relay 12volt SPST 30amp Radio Shack P/N 275-0226
Connector. Four contact trailer lights type. For switched power from joy stick relay to Diverter.

I rosette welded the threaded pieces to the tube. Then brazed the washer in place and silver brazed the one eighth inch square stock to the tube.
 

·
Registered
Joined
·
446 Posts
View attachment 9125
View attachment 9126
View attachment 9127

Joy Stick
Tubing, 1/2in Dia. X .049 wall thickness
2ea. 1/2 x 13 bolts machined to make end parts and Jam nuts.
1inch of 1/8 x 1/8 bar stock
5/16 washer bored to 1/2in ID for handle stop
JD handle Base, P/N M126552 $2.69 and Cap P/N M126553 $1.63
Push button switch used was Alco MPG 206R with weather boot seal
Relay 12volt SPST 30amp Radio Shack P/N 275-0226
Connector. Four contact trailer lights type. For switched power from joy stick relay to Diverter.

I rosette welded the threaded pieces to the tube. Then brazed the washer in place and silver brazed the one eighth inch square stock to the tube.
I know this is an old thread, and it's been a month since DirtRod had been here, but I hope he sees this.

How does this knob (which is normally on the lever for selecting the gear range) feel in comparison to the standard loader knob...ergonomics wise??
 

·
Registered
Joined
·
776 Posts
I made a simple tubing bender from a couple of pulleys and duplicated the stock shape and location.
The base that the joystick mounts was re drilled and taped for the the
Just found this... Super nice!
 

·
Registered
Joined
·
29 Posts
Reinstall boot

Dirtrod, thanks for sharing this mod. I used your design and made a new joystick for my 1026r. However, I haven't figured out how to get the boot reinstalled. One guy said you could reach it from underneath with long nose pliers. How did you get the boot back in place?
 

·
Registered
Joined
·
776 Posts
I think we need one of the fabricators out there (maybe KennyD!?) to build a kit based upon this design and the parts utilized. :)
 
1 - 14 of 14 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top