Green Tractor Talk banner

1 - 20 of 34 Posts

·
Registered
Joined
·
523 Posts
Discussion Starter #1
I dropped my BB on the way out to pickup the trash cans to attempt some pot hole filling. When I lifted the BB, I noticed it was way off level. The stud on the turnbuckle assembly sheared off right where it transitions to the larger hole size. I'll get a pic posted later. This is the stud that holds the draw arm and lift rod together. Names may be off.

Haven't heard of this one before. I keep the turnbuckles tight, but still have a little play, so I'm not sure what caused it.

Does anyone know the replacement part number? I am guessing I'll have to get the whole turnbuckle assembly.
 

·
Registered
Joined
·
4,260 Posts
Here his the hitch.




Three Point Hitch
CartkeyPART NO.PART NAMEQTY SERIAL NO.REMARKS
114M7401Lock Nut2 M12
245M7051Pin Fastener2 16 X 55 mm
3AA21292Quick Lock Pin2
4AM137744Tie-Down Strap1
5AR60372Quick Lock Pin1
6AR62150Quick Lock Pin2
7LVA16294Draft Link2
8LVA16295Lift Link1 Fixed
9LVA16296Lift Link1 Adjustable
1014M7335Nut2 M20
CartkeyPART NO.PART NAMEQTY SERIAL NO.REMARKS
11LVA16683Sway Chain2
12LVA16811Link2
13LVA16812Link2
14LVU22244Turnbuckle2
15M123745Pin1
16M154221Cotter Pin2
17LVA16650Center Link1
 

·
Premium Member
Joined
·
13,425 Posts
Here his the hitch.




Three Point Hitch
CartkeyPART NO.PART NAMEQTY SERIAL NO.REMARKS
114M7401Lock Nut2 M12
245M7051Pin Fastener2 16 X 55 mm
3AA21292Quick Lock Pin2
4AM137744Tie-Down Strap1
5AR60372Quick Lock Pin1
6AR62150Quick Lock Pin2
7LVA16294Draft Link2
8LVA16295Lift Link1 Fixed
9LVA16296Lift Link1 Adjustable
1014M7335Nut2 M20
CartkeyPART NO.PART NAMEQTY SERIAL NO.REMARKS
11LVA16683Sway Chain2
12LVA16811Link2
13LVA16812Link2
14LVU22244Turnbuckle2
15M123745Pin1
16M154221Cotter Pin2
17LVA16650Center Link1
These diagrams, just trying to help, so would it be #13??
 

·
Registered
Joined
·
523 Posts
Discussion Starter #5
Excellent, Thank you. #13 is the part I am looking for.

BB is for Box Blade. I have a Frontier 2048L I believe. I'll have to look in my signature.
 

·
Bonehead Club Lackey
Joined
·
10,266 Posts
I dropped my BB on the way out to pickup the trash cans to attempt some pot hole filling. When I lifted the BB, I noticed it was way off level. The stud on the turnbuckle assembly sheared off right where it transitions to the larger hole size. I'll get a pic posted later. This is the stud that holds the draw arm and lift rod together. Names may be off.

Haven't heard of this one before. I keep the turnbuckles tight, but still have a little play, so I'm not sure what caused it.

Does anyone know the replacement part number? I am guessing I'll have to get the whole turnbuckle assembly.
Here his the hitch.




Three Point Hitch
Cart
key
PART NO.
PART NAME
QTY
SERIAL NO.
REMARKS
1
14M7401
Lock Nut
2
M12
2
45M7051
Pin Fastener
2
16 X 55 mm
3
AA21292
Quick Lock Pin
2
4
AM137744
Tie-Down Strap
1
5
AR60372
Quick Lock Pin
1
6
AR62150
Quick Lock Pin
2
7
LVA16294
Draft Link
2
8
LVA16295
Lift Link
1
Fixed
9
LVA16296
Lift Link
1
Adjustable
10
14M7335
Nut
2
M20
Cart
key
PART NO.
PART NAME
QTY
SERIAL NO.
REMARKS
11
LVA16683
Sway Chain
2
12
LVA16811
Link
2
13
LVA16812
Link
2
14
LVU22244
Turnbuckle
2
15
M123745
Pin
1
16
M154221
Cotter Pin
2
17
LVA16650
Center Link
1
Excellent, Thank you. #13 is the part I am looking for.

BB is for Box Blade. I have a Frontier 2048L I believe. I'll have to look in my signature.
Ok, you said it's #13. Now where does it go into a larger hole size? You got me stumped. :dunno:
 

·
Registered
Joined
·
4,260 Posts
Levi,
It goes into the hole in the middle of the lift arm. The bottom of the lift link also aligns with this hole and the turn buckle bolt.

Highlighted in the yellow outlined square.
0002884832____________A2.jpg
 

Attachments

·
Registered
Joined
·
523 Posts
Discussion Starter #9
Thanks for the help. $19 for the link and nut. Surprising at the least. I assumed this assembly would be high dollar.

I'll get a pic if it ever quits raining here.
 

·
Registered
Joined
·
146 Posts
Thanks for the help. $19 for the link and nut. Surprising at the least. I assumed this assembly would be high dollar.

I'll get a pic if it ever quits raining here.
Fred,
When you get the part and replace it make sure it is installed with the eye at a right angle to the DRAFT LINK, It makes a difference. I had to adjust the LINK on my 2210 as it was flat to DRAFT LINK and wouldn't adjust properly. JUST PASSING ON KNOWLEDGE Acquired from others.

waltmart
 

·
Registered
Joined
·
110 Posts
I have broke several

I got tired of them braking. And they always broke when using the box blade
So I modified the linkage to this

AF5ABCC6-8F3B-428B-AB2C-CB91BAF2B000.jpeg
https://www.stevenstractor.com/accessories/three-point-hitch/leveling-rods-side-links/turnbuckle-1.html
This may not be the same size I got but you can check the od of the pin, and measure the length. The I drill the bar and mounted / a unbolt to the bar.
If there is any interest let me know and I’ll get more info. And a pic. I have had to replace my ubolts a few times but they are only 2 or $3. But know I now better what works and they are lasting. Over 1.5 years since last replacement. Total hrs 1254.
 

·
Registered
Joined
·
40 Posts
I got tired of them braking. And they always broke when using the box blade
So I modified the linkage to this

View attachment 548313
https://www.stevenstractor.com/accessories/three-point-hitch/leveling-rods-side-links/turnbuckle-1.html
This may not be the same size I got but you can check the od of the pin, and measure the length. The I drill the bar and mounted / a unbolt to the bar.
If there is any interest let me know and I’ll get more info. And a pic. I have had to replace my ubolts a few times but they are only 2 or $3. But know I now better what works and they are lasting. Over 1.5 years since last replacement. Total hrs 1254.
I for one am interested in more info - I've broken about 4 of these over time, while using BB. Can you please post a photo of your setup? Thanks for link!
 

·
Registered
Joined
·
110 Posts
Ok

I for one am interested in more info - I've broken about 4 of these over time, while using BB. Can you please post a photo of your setup? Thanks for link!
I’ll try to get it done after church tomorrow
 

·
Registered
Joined
·
523 Posts
Discussion Starter #17
Yeah, I can't get a picture to load.

I graded out the potholes this weekend without the turnbuckle, just a bolt. Did a good job expect the track was a little wobbly.
 

·
Registered
Joined
·
110 Posts
Note

Don’t understand why I can’t post the photo here it let me post the 1st one.
Any way it let me add it to my profile so go there and get it
There is more than one size make sure to measure the pin dia. And length. You need to stay close to the same mounting location or you will get into the tire. With the quick hitch on. I can get it tight but I am to the point we’re the is nothing left to take up. And I would use locking nuts.
 

·
Registered
Joined
·
523 Posts
Discussion Starter #20
Here is the picture of where it broke. Couldn't get it to load at home, but it did at work.

aaa-13.jpg
 
1 - 20 of 34 Posts
Top