[stone7]

Does anyone have the PDF installation instructions
for the BW16139 ?

Thanks

 

[Kennyd]

:wgtt:

Like I mentioned in the other thread, PM user JD110, he may have them. Is there something specific you need? JDParts has the part blow up if that will help?

 

[stone7]

OK, JDparts will do.

I wanted to know if this kit includes hoses to simply
plug into the rear 3rd hydraulic valve.

Or if it is plumbed into the hyd system some other way.

Thanks.

 

[Kennyd]

3rd function for 400c & cx loader correct?

From JDParts:

HYDRAULIC HOSES AND OIL TUBES - THIRD FUNCTION

Cart	KEY	PART NO.	PART NAME	QTY	SERIAL NO.	400X	400CX	REMARKS
	1	M42702	SNAP RING	4	X	X
	2	AW32609	LINE	2	X	X
	3	W45635	PLUG	1	X	X	(A) (ORANGE)
		........	PLUG	1	X	X	(B) (C) (ORANGE)
	4	AW30147	HYDRAULIC HOSE	2	X	X	3/4" X 1 800 MM (70-3/4") X 11/16"
	5	W45608	CAP	1	X	X	(A) (ORANGE)
		........	CAP	1	X	X	(B) (C) (ORANGE)
	6	AM105467	HYDR.QUICK COUPLER PLUG	2	X	X	(A)
		AR94522	HYDR.QUICK COUPLER PLUG	2	X	X	(B)
	7	W45609	CAP	1	X	X	(A) (BLUE)
Cart	KEY	PART NO.	PART NAME	QTY	SERIAL NO.	400X	400CX	REMARKS
		W42991	CAP	1	X	X	(A) (GREEN)
		........	CAP	1	X	X	(B) (C) (GREEN)
	8	AW32949	HYDRAULIC HOSE - FABRICATE	2	X	X	3/4" X 2 500 MM (98-1/2") X 3/4"
	9	W42411	CAP	1	X	X	(BLACK)
		........	CAP	1	X	X	(B) (C) (ORANGE)
	10	R105388	TIE BAND	4	X	X
	11	W45634	PLUG	1	X	X	(A) (BLUE)
		........	PLUG	1	X	X	(B) (C) (GREEN)
	12	W50355	BRACKET	1	X	X
	13	LVA12997	HYD. QUICK-CONNECT COUPLER	2	X	X	(A) 3/8" COUPLER
Cart	KEY	PART NO.	PART NAME	QTY	SERIAL NO.	400X	400CX	REMARKS
		LVA13231	HYD. QUICK-CONNECT COUPLER	2	X	X	(B) 1/2" COUPLER
	14	AW32585	OIL LINE	1	X	X
	15	AW32586	OIL LINE	1	X	X
	16	W44542	BLOCK CLAMP	1	X	X
	17	W52153	SCREW	1	X	X	(SUB FOR 19M8040, THIS APPLICATION)
	18	M70728	CAP	1	X	X	BLACK
		W53377	CAP	1	X	X	1/4" (GREEN)
	19	X4010-T6	HYDR.QUICK COUPLER PLUG	1	X	X	(SUB FOR AW32184)
	20	32246	O-RING	1	X	X
	21	AM102487	HYD. QUICK-CONNECT COUPLER	1	X	X
Cart	KEY	PART NO.	PART NAME	QTY	SERIAL NO.	400X	400CX	REMARKS
	22	M85099	PLUG	1	X	X	BLACK
		W53387	PLUG	1	X	X	1/4" (ORANGE)
	23	W50244	HOSE CLAMP	6	X	X
	24	19M7286	CAP SCREW	2	X	X	M6 X 25
	25	14M7272	NUT	2	X	X
	26	AR94522	HYDR.QUICK COUPLER PLUG	2	X	X
	27	........	CAP	1	X	X	(B) (C) (GREEN)
	..	AW28043	PLUG	1	X	X	(DUST CAP AND PLUG) (CONTAINS (6) COLOR CAPS AND (6) COLOR PLUGS
	..	AW34729	QUICK COUPLER KIT	1	X	X	(COUPLER CONVERSION) (CONTAINS (4) AR94522 AND (4) COLOR CAPS)

(A) FOR MACHINES WITH 3/8" COUPLERS PRIOR TO 1NOV.06(A) POUR MACHINES AVEC RACCORDS 3/8" ANTERIEURES AU 1ER NOV. 06(A) FUER MASCHINEN MIT 3/8" KUPPLUNGEN (VOR 1 NOV. 06)(A) PER MACCHINE CON GIUNTI DA 3/8", PRIMA DEL 1 NOVEMBRE 06(A) PARA MAQUINAS CON RACORES DE 3/8" ANTERIORES A 1 NOV 06(B) FOR MACHINES WITH 1/2" COUPLERS(B) POUR MACHINES AVEC RACCORDS 1/2"(B) FUER MASCHINEN MIT 1/2" KLUPPLUNGEN(B) PER MACCHINE CON GIUNTI DA 1/2"(B) PARA MAQUINAS CON RACORES DE 1/2"(C) ORDER AW28043(C) COMMANDER AW28043(C) BESTELLE AW28043(C) ORDINAIRE AW28043(C) PIDASE AW28043







The short answer to your question is Yes.:thumbup1gif: The hoses are 70 3/4" long.

 

[xcopterdoc]

PM me.

 

[stone7]

BW16139 How-To

This is the BW16139 kit laid out.

One of the bottom lines was missing, which the dealer very helpfully resupplied.
It's a little bit of a puzzle to see how everything fits together. But there are
two identical things of each, except for the bottom lines. I guess they left one
out just for fun. Or to see how long I would procrastinate. About a week!

Looking over the kit, every fitting has an O ring except the end for the
third function coupler. I used the eyedropper to wet each O ring fitting before
tightening. And I used Permatex teflon pipe dope for the coupler.

The two bottom lines need to be positioned in between the existing plumbing. And then
another slotted holder is attached using a longer bolt on to the existing holder. This takes
a little muscle. They don't go easily into the slots on the plastic holder. Some
WD 40 might have helped. And getting the new longer bolt into the tapped hole is
a little difficult. I used a quarter inch drive ratchet with a long extention, so I
could use both hands to push and turn. This worked fairly well.

There are two green holders that clamp the bottom lines directly over top of two existing
lines. These holders have little tabs that help align and mate them together.

I tightened them until the center section was completely tight, showing no gap.

A third green holder attaches on top of an existing black holder using a longer bolt.

On back of the two straight lines, the hoses connect and are inserted through the
black mesh protector, along side the existing lines. I couldn't find a large black zip tie,
so two smaller ones will do for now.

The new bracket and the rear hoses are fairly straight forward.

My paint shop is a couple of rattle cans, and some prep solvent. So for now I just
drape the rear lines over the open station and hook them up.

Powder coating the bracket would have been nice. And a couple of big black zip ties
would have been appreciated. And use a nice big box or a better bag to ship stuff.
The bag was in tatters with large cuts.

This is a very easy kit to instal and it makes the indispensable 400X loader even more useful.
Thank you John Deere for making it available.

 

[Kennyd]

Great follow up Stone, thanks for sharing:yahoo:

 

[56FordGuy]

Great post, Stone. :thumbup1gif:

 

[BigGTP]

Great looking pics. Getting ready to install this on my 4320 does anyone have step by step instructions for this install? Glad I found this site!!!

 

[Kennyd]

Great looking pics. Getting ready to install this on my 4320 does anyone have step by step instructions for this install? Glad I found this site!!!

Yes. see attached and welcome to GTT.

 

[BigGTP]

A big thank you !!!