Green Tractor Talk banner

1 - 9 of 9 Posts

·
Registered
Joined
·
55 Posts
Discussion Starter #1
Hello all. I bought a reversible cutting edge for my heavy duty bucket, 73". It didn't come with mounting hardware. Does anyone know the spec's on the plow bolts and nut type?
 

·
Premium Member
Joined
·
10,068 Posts
Where did you get the cutting edge?

My local dealer has a bin of plow bolts, you could carry yours down and match them up. I'd recommend nylock nuts.
 

·
Registered
Joined
·
55 Posts
Discussion Starter #4 (Edited)
Got it in a auction. I was hoping to buy the hardware from fastenal or a hardware store rather than my dealer. I've already seen the cost for the cutting edge...
 

·
Premium Member
Joined
·
10,068 Posts
If your edge is meant for standard plow bolts, you'll need to go to a dealer or ag supply store. What size holes do you have? Are they round or square? Without a model number or any identifying info for your cutting edge, it's very difficult to say what it may require.

For what it's worth, my dealer sells hardware by the pound. Plow bolts are a consumable part and aren't that expensive.
 

·
Premium Member
Joined
·
745 Posts
Hello all. I bought a reversible cutting edge for my heavy duty bucket, 73". It didn't come with mounting hardware. Does anyone know the spec's on the plow bolts and nut type?
I would almost bet the farm that the bolts are standard grade 5 plow bolts, be aware they come in a clipped and oval head style that you most want to avoid. The bolts come with standard nuts, but either type will work. You'll have to do some investigation (measure side to side in the square hole) to determine your bolt size then get the length you'll need. I think mine were 1/2" by 2" (could have been 3") and I cut the excess bolt threads off flush with the nut, and it looked like this when completed.

All the best.
 

·
Registered
Joined
·
55 Posts
Discussion Starter #7
It has BW14763 written in grease pen on it. I believe that is the exact JD part that I needed. I've pretty much exhausted looking on-line as this part number states hardware included. Can't find anything specific about the hardware itself.
 

·
Premium Member
Joined
·
10,068 Posts
It has BW14763 written in grease pen on it.
Bingo! :good2:

Your part number comes up as fitting the 553 loader, along with several others. I went to JD Parts and pulled up the 553 loader and found your cutting edge listed.

You want 1/2" plow bolts, in either 1 3/4" (10H1034 JD number) or 2 1/4" length (10H1236 JD number). The 1034 is $1.09 at GFP, and the 1236 is $1.80. I would suggest you try a local farm supply or dealer, they should have them in bulk.

cuttingedge1.jpg


1......Cutting Edge1(D) (ORD BW14763)
W43874Cutting Edge1(D) (USE WITH BW14267)
214H809NutAR1/2"
310H1236Bolt181/2" X 2-1/4"
10H1034Bolt121/2" X 1-3/4"
4E62934Flange Nut16
5W52238Tooth8
6W41284Plate2(C)
710H1034Bolt161/2" X 1-3/4"
8W53248Plate1(C) RH
CartkeyPART NO.PART NAMEQTYSERIAL NO.REMARKS
9W50734Lug1(C) RH
10W52745Hook2(C)
11W50733Lug1(C) LH
12W53249Plate1(C) LH
13......Loader Bucket1
14......Loader Bucket11850MM
15W43312Cutting Edge1(C) (D)
16W44429Cutting Edge1(D)
17BW14763Cutting Edge1(B) (D) 1910mm
BW14267Cutting Edge1(B) (D) 2150MM
CartkeyPART NO.PART NAMEQTYSERIAL NO.REMARKS
18BW15763Tooth1(B)
19BW15543Loader Bucket1(B) 1850MM
BW15545Loader Bucket1(B) 2150MM
20BW15544Loader Bucket1(A) (B) 1850MM
(A) HEAVY DUTY BUCKET

(B) COMPLETE GOODS/SHIP BUNDLE(C) WELD ON(D) CUT TO LENGTH
 
1 - 9 of 9 Posts
Top