Green Tractor Talk banner

1 - 5 of 5 Posts

·
Registered
Joined
·
107 Posts
Discussion Starter #1
I've searched around but haven't been able to locate what the specs are for the hoses for the angling cylinder when used on the 1025 Quick Tatch bracket. I'm moving the cylinder over from my old 425 setup and all I need are the longer hoses. So if anyone has already done this I'd greatly appreciate the info.

For the angling cylinder JD parts catalog indicates M91486 hose "cut to length" so no help there. My thought is just to get generic hoses from Surplus Center.

It *looks* like about 64" length?
 

·
Premium Member
Joined
·
1,853 Posts
I don't find where M91486 is listed in the parts catalog for the angling cylinder. When I searched that # on JDParts, it shows it as 120". Guessing it's just bulk hose.

The part numbers I see listed are LVA21772 (2261 mm) & LVA21773 (2146 mm). BLV10880 is listed as the complete kit (cyl, hoses, brkts, etc).

Winter of 2017 I got the front quick hitch, blade etc. Seems to me that the BLV10880 was superceded to LVB26108, which is what I got & installed. The hoses that came with it were:

Black cap: AM132313 (listed as 79.724")
Yellow cap: AM132314 (listed as 85.236")

Seems to me that they were about 6' long or so. They're listing them at 6'7" & 7'1", so that sounds right. I can measure them tmrw if you need.

From the pictures I took when I installed it, it looks like the lift cyl hoses are LVA21770 & LVA21771. Those are consecutive numbers to the LVA21772 & 773 they are listing now, so the AM132313 & 314 were either substitutes or are the replacements that the catalog isn't showing yet. Either way, they work fine.

Hope that helps.
 

·
Registered
Joined
·
107 Posts
Discussion Starter #3
I don't find where M91486 is listed in the parts catalog for the angling cylinder. When I searched that # on JDParts, it shows it as 120". Guessing it's just bulk hose.

The part numbers I see listed are LVA21772 (2261 mm) & LVA21773 (2146 mm). BLV10880 is listed as the complete kit (cyl, hoses, brkts, etc).

Winter of 2017 I got the front quick hitch, blade etc. Seems to me that the BLV10880 was superceded to LVB26108, which is what I got & installed. The hoses that came with it were:

Black cap: AM132313 (listed as 79.724")
Yellow cap: AM132314 (listed as 85.236")

Seems to me that they were about 6' long or so. They're listing them at 6'7" & 7'1", so that sounds right. I can measure them tmrw if you need.

From the pictures I took when I installed it, it looks like the lift cyl hoses are LVA21770 & LVA21771. Those are consecutive numbers to the LVA21772 & 773 they are listing now, so the AM132313 & 314 were either substitutes or are the replacements that the catalog isn't showing yet. Either way, they work fine.

Hope that helps.
Very helpful - thanks. I've been using the JD Parts Catalog for years and I still sometimes can't find things.
 

·
Premium Member
Joined
·
2,065 Posts
Here are some pictures of the angle cylinder hoses off my 1025R.

The hose is 1/4" - 100R17 - 3000 PSI. Each hose has a 90 degree #6 O-ring Face Seal Swivel (ORFS) on one end and on the other end a straight #6 ORFS

If you are going to use aftermarket 1/4" QC plugs with 1/4" NPTF thread like these (https://www.hydraulicstore.com/connectors/quick-couplers/hydraulic/ag-couplers/iso-5675/standard/plugs/poppet/qch-agpop-t-14-14fp-s.html), then you should get the hoses made with 1/4" NPTM straight ends on end opposite the 90 degree end and then use these 45 degree adapters https://www.hydraulicstore.com/connectors/steel-adapters/pipe-thread-nptf/5503-adapters-45-degree-street-elbow?page=1 and the 14" NPTF QC listed above.

If you are using JD OEM QD, then these would be the hoses..
One hose: https://www.hydraulicstore.com/hac?code=R1704A-A26S66-08400

Second hose: https://www.hydraulicstore.com/hac?code=R1704A-A26S66-07500
 

Attachments

·
Registered
Joined
·
107 Posts
Discussion Starter #5
Here are some pictures of the angle cylinder hoses off my 1025R.

The hose is 1/4" - 100R17 - 3000 PSI. Each hose has a 90 degree #6 O-ring Face Seal Swivel (ORFS) on one end and on the other end a straight #6 ORFS

If you are going to use aftermarket 1/4" QC plugs with 1/4" NPTF thread like these (https://www.hydraulicstore.com/connectors/quick-couplers/hydraulic/ag-couplers/iso-5675/standard/plugs/poppet/qch-agpop-t-14-14fp-s.html), then you should get the hoses made with 1/4" NPTM straight ends on end opposite the 90 degree end and then use these 45 degree adapters https://www.hydraulicstore.com/connectors/steel-adapters/pipe-thread-nptf/5503-adapters-45-degree-street-elbow?page=1 and the 14" NPTF QC listed above.

If you are using JD OEM QD, then these would be the hoses..
One hose: https://www.hydraulicstore.com/hac?code=R1704A-A26S66-08400

Second hose: https://www.hydraulicstore.com/hac?code=R1704A-A26S66-07500
Extremely helpful Ray. Many thanks!
 
1 - 5 of 5 Posts
Top